I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
We are using QSPI to connect nrf52840 DK with nand flash of AS5F34G04SND. In page 28, 29, and page 17-table 2-1 of datasheet of the flash, we need to Program load x4 IO: sending...
I am on a custom NRF54L15 module where I want to change the default UART TX pin from P1.04 to P2.07. Unfortunately, there is no output. Using P1.14 somehow works? I also have...
Using nrf connect 3.1.1
using nrf54L15 evaluation board.
Hi,
I have an application that is using the shell capabilities of the zephyr. uart and shell is connected...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I have been trying to return set uart in low power mode and resume uart low power from a button press...
Hi, I interfaced the Quectel EC200U GSM module with the nrf5340dk. Now I want to do the FOTA with the help of GSM . Is there any example documents or any experince. And also...
I am trying to make the nrf9161 go to very low power mode for 10 seconds and then come back online.
Actually I would not mind if it were to start all over again when coming...
Hello,
I am using the example on the Nordic DK to get UDP messages from the Hologram API to the Nordic Modem. AT#XUDPSVR=1,6002 #XUDPSVR: 3,"started" OK
I very inconsistently...
Hello,
I am working with the nRF9151 board and trying to read SIM/eSIM information.
Steps I followed:
Used nRF Programmer → Erase all.
Opened Board Configuration ...
Dear Nordic
We are evaluating a wearable device and plan to use nRF54H20 be our MCU,
Since our device will be a small form factor and Nordic not released datasheet yet...
Hi, I'm working on nRF9151 on custom board, NCS 3.1.0 and I'm building application with TF-M enabled. I've encountered quite a strange problem. If I remove all UART instances...
Hi,
using nrf sdk connect 3.1.1
using nRF54L15-PDK evaluation board.
Steps to reproduce issue:
1. Setup my board into low power. my branch mark is ~2.9uA.
2. Perform...
I use BLE for one-to-many connections. Usually, the peripheral device should first broadcast, then establish the connection for communication, and finally disconnect. However...
Hello,
We are developing a product based on the nRF54L15, using BT Mesh. We also use the FLPR. For communication between the cores, we use ICMSG.
Separately, ICMSG and...
