Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi.
I am looking to implement a nRF52840 chip in my 5v battery operated door lock.
Sorry if this is asked before or should be clear from documentation, but I am not...
Hi,
Do you have an example of how to implement a serial console with nrf connect 1.4.99-dev1 with nrf5340_REV1, I tried compiling usb_uart_bridge but got following error...
There are two central sd_* methods for writing to flash - write and erase. The problem is I need to know where I can put my data without trashing something else that is already...
I have two projects exhibiting the same problem.
I have custom board using the nRF52832 and another using the nRF52840. In both cases I am using nRF5 SDK latest version...
Hello,
I would like to have confirmation that the NRF52 will be compatible with my need.
The NRF52 must be able to be connected to a smartphone, while receiving advertising...
I have problems with my custom board.
I developed the firmware with the nrf52832-dk custom and there the firmware runs standalone (with RTT logs on and without) . but now...
I use a nRF52840 Dongle as the Sniffer HW. I use 2 other nRF52840 boards, one is a peripheral (NUS) and the other is a central/peripheral (NUS). The cen/per connects as a...
Hi I have a custom nRF52840 board, and I have a current BLE UART setup. I also want to communicate with a IMU module via serial connection. Can you point me in the direction...
hi,
ncs1.4.0\nrf\samples\bluetooth\peripheral_uart， The LBS service was added, but Advertising faile.
I don't know that I made a mistake in that step. It may be the address...
If I upload the pre-compiled asset_tracker file to the Thingy91, it works fine. If I compile it myself and try to upload it, nothing happens. It shows the write is successful...
I am trying to implement fstorage in my application using nRF52840, soft device 140, SDK for Mesh v4.0.0. and SDK 16.0.0 and Segger Studio.
Based on the fstorage example...
Hello,
I'm trying to develop a wearable stacking form-factor where number of boards can be assembled in a deck: MCU, sensors, actuators, power supplies, etc. Size of the...
Hi ,
I want to compile mesh examples .I tried it using segger ide Alternatively,I wish to compile it in cmake too. Can you please tell me the procedure to compile code using...
Hi,
I was able the configure the sample to connect to AWS but I cannot figure out where the cloud_send function is sending the data. Is there any documentation on where...
Hi all,
I am using a nRF52840-DK as SPI slave with a MSP430 as host SPI master for a nRF8001 replacement application.
As I am absolutely not familiar with high level functions...
