after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
Im a beginner in microcontrollers programming, just started with the pca10056 and pca10059. Im aiming to develop a beacon scanner for pca10059, to send data via usb...
I compiled and debugged the PCA10040e ANCS example (ie emulating the 52810 using the 52832) from SDK 15.3 - successfully. But I wanted to turn off code optimization to facilitate...
Hello,
As many mobiles do not have NFC I would like to use LESC OOB pairing with an QR-Code which could be shown on the device terminal. Well, I know where the NDEF message...
SDK version :15.2
question； when i use app_timer , i got interrupt which is not i wanted.
i creat and start timer :
app_timer_create(& m_timer ,APP_TIMER_MODE_REPEATED...
I'm using nRF SDK V15 with nrf52DK board, running the ble_app_hids_ms example.
I I want to have continuous non-stop advertising duration, should I have both APP_ADV_FAST_DURATION...
Dear Sir/Madam,
My question regards the behavior of the EasyDMA during the transfer of data to / from a serial peripheral like SPI or UART.
Let's suppose that during the...
Hi all,
I using SDK 15.1 and 15.3 for test.
I am working with DFU for NRF52810.
I tried success for NRF52840.
But I can't update success for NRF52810.
Below is scrip...
I use the Firmware «AT host sample» on Thingy91. Then I connect to Swisscom network on band 20. The current consumption is about 3.5mA. Then I send AT+CFUN=0 or AT+CFUN=4...
Hi All
We are using nRF9160 DK, and we are working on ADC channel. we use This example of ADC. I am using single-ended with no over-sampling with a gain of 1/6, reference...
Hello
my setup is sdk 15.3, nrf52840, s140, open bootloader and an application.
Everything is merged, flashed and running and no changes are made at the standard addresses...
I am currently developing a peripheral app on a custom board with a nrf52832 chip on it and connecting to the device using QT's ble library. I'm having issues where my connection...
I want to turn on /off LED by advertising TX of BLE
peripheral : nrf52810 central : nrf52840 Specifically, peripheral performs advertising TX, The central processes LED...
