after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi all
Is possible have DFU in the peripheral side to update a Central app program? Is there example doing it?
I have a Peripheral (custom board nRF52 dongle) connected...
Hi
We use the nRF52832 together with other devices in a housing. Some of the other devices may produce quite a lot of heat. Therefore we wanted to use the temperature sensor...
Hi,
i am trying to flash the softdevice bootloader in Sparkfun nRF52832 breakout board using RPI2 + openOCD through SWD. debug port initialize is failed all the time.i...
I have a couple of questions regarding Radio transmission for BLE.
Is the radio driven by one of the HFCLKs? If so, it confuses me how a 16M clock can drive/derive...
Hi,
I have initial flashed boot loader and application based on SD version 3.1 and SDK 12.2.0
with
DFU_APP_DATA_RESERVED CODE_PAGE_SIZE * 3
FDS_VIRTUAL_PAGES 3...
I am using a nrf52 development kit as a peripheral to send data . It is working fine if I use the nrf Toolbox app on my phone, but is there anyway that I can see the 'raw...
Hi,
I configured openOCD and gcc compiler. But i got following error.
i gave following command on terminal.
i created one file that is manual.cfg
and contain in that...
Hi all,
someone can please explain to me how works the indication?
How can i read the value of cccd in the APP?My problem is understand if the APP is ready to receive...
First attempt at implementing buttonless dfu; assistance would be greatly appreciated. Using SDK v11 + s130 + nRF51822.
Please note that iphone screen captures supporting...
Hello,
I am still having troubles with the BLE_GATTC_EVT_TIMEOUT. The problem is that the error is not happening frequently and is hard to reproduce. It is also hard to...
I was building my own custom application that connects a nrf_drv_timer to an ADC start trigger using PPI on an nRF51822 and I could not get it to work. I asked a previous...
Hi
I have ported a simple function from nRF51 to nRF52 which Outputs PWM coded Startup Diagnose Information via a GPIO.
The Timing is generated by wait Loops and GPIO will...
I am using the nRF Connect Tool, everything is working fine (Y)
My question is related with the Log file, is there any way to get in the Log File only the data sent through...
Hi,
I am new to nrf52 series and I have just started playing with NRF52 series Development kit. I am working on a project that requires the functionality of both ANT and...
