Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Using nrfx_timer_extended_compare I would like to periodically adjust the compare value of a running timer. It seems to work without disabling the timer before this and re...
Hi，
Dear， I have a question about Fstorge and Bootloader. If my app layer calls the Fstorge API to store some data, will the data saved by the Fstorage API be erased when...
Hello All,
I am running into a mesh assert error when running the light switch server demo on a custom board w/ the NRF52840 (MDBT50-1M). The device starts up fine, has...
Hi all
I am studying mesh example such as light switch server, I use Segger Embedded Studio to comple the project of light switch, it is OK, but when I want to do online...
Hi,
I'm developing a BLE DFU controller with bluepy on a RPi3. The peripheral that is being updated is a nRF51 device on SDK 12.3.0, with the secure bootloader and experimental...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi,
In y project, I want to implement CTS. Until now it's been working, but I don't know why, I now have this problem: Current Time Service not found on server, which means...
I am using a Sparkfun Pro nRF52840. I wish to communicate with it serially. I found the UUIDS it exposed : UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E TX Characteristic...
Hi,
I am using nrf51 dk with sdk 12.3 and softdevice S130 bluetooth module using Keil IDE.In our project we need to send sensor data from the nrf51 bluetooth module to another...
Hello,
I want to add central-role features to my peripheral firmware. I've already managed to get this work. The strange thing, I only get one BLE_GAP_EVT_ADV_REPORT. So...
Hello.
I just import Thingy firmware: thingy52_ses.zip and try to build this project and check possibility of programming my Thingy, but SEGGER returns something like that...
When I use nRF52840 dongle as a promiscuous packet sniffer , I found that sniffer works fine no matter how much I set the baud rate. This happens only on the dongle, so I...
Hello,
I have a PWM code that works as a peripheral application on my nRF52 DK, but now I want to set it to be controlled via android phone app. I have nrf connect on my...
Hello,
I'm a newbie to BLE and the Keil uvision IDE. I'm using a nrf51422_xxac_s110 chip, The version of the IDE I'm using is 5.28.0.0. When I add the fds.c file, into the...
