Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am new in this community and I am trying to get started with developments using nRF52840 DK. I am using SDK 13.0 for the library and I compile my code using armgcc...
I would like to be able to leave the bootloader installed and debug an application. I have been able to use the merge tools to get the hex files all merged and generate the...
Hi, i'm currently working on a low power sensor device based on nrf52832. I want to transfer data only to bonded central devices. Priority is using static passkey, but my...
After reading a few related questions and the official tutorial, I have a guess, hoping to confirm:
If I do not need to add extra events into schedular for management purposes...
I'm doing experiments on high throughput and need to call sd_ble_gatts_hvx, but there are a lot of confusing things so it's hard to get started.
If I want to know if notify...
Hi,
I have a nRF24LE1 development kit and a starter kit. If I turn the power off and turn the power back on using the power switch S9 on the motherboard. The nRF24LE1 chip...
I am using pc-ble-driver-py to configure an nRF52832 demo board as a BLE central device. I currently have the heart_rate_collector.py example working. However, what I would...
I am build a sound client project
when I received the data from the thingy52（which is sound server device）
the I play the sound by function drv_speaker_ble_pcm_play...
Hello,
I'm trying to interface this cheap OLED display from ebay
and while running and debugging the code I think should work(all based off the TWI_sensor sdk example...
Hello All,
I am working on Raytac module based on nrf51822 with ble_app_uart code. I can see on module there is no external crystal ,
my module is not able advertise,...
dear nordic employee
I have two thingy，one of witch is the sound server（nordic provide）
now ，I want to do a sound client，I have learned the service knowledge
but...
Hi there,
I'm currently porting the nRFgo gzll_host_w_dyn_pairing_example however my microcontroller does not have an aes encryption peripheral.
It seemed easy to just...
Hello Dev Zone,
We've been using the IoT SDK 0.9 all year and recently ported to the production release bundled with the SDK 14.1 package.
We have the DFU working with...
Hi,
I am using SDK14.1 with nrf52832 and want to write to eeprom memory over SPI from BLE characteristic call.
My spi module works and everything was working fine until...
Hi,
I'm using a nrf52 custom board based out of the telit bluemod s42. I'm trying to port the ble_app_uart example of the SDK14 onto the custom board.
The code seems to...
