Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I got a problem.
I created a timer, interval is 30ms.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(150, UNIT_10_MS) /**< Minimum acceptable connection interval (0.02...
Hey Guys,
I am trying to create a workflow for creating new project from scratch in eclipse, traditional way with nRF5 sdk provided make file is not scalable and it really...
We are using a MMA8452Q accelerometer connected to an nRF51822 via TWI using the twi_hw_master. Reading the WHO AM I register is the first attempt to get the TWI running but...
Hi,
let's say I program flash with SD, Booloader and merged App1&Ap2 images. I need to switch application (only once, after some self tests) using some command from application...
I am having an odd problem.
nRF52
softdevice S132 V2.0.0
I have a bootloader and application. when I program them directly to the device they both work fine and can...
I need to get three ADC data from acceleration sensor with nrf51822. I tested getting a ADC data using simple_adc_pca10028(Keil_v5/ARM/Pack/NordicSemiconductor/nRF_Examples...
Hello
We are about to move an old design based on the NRF51 to the more powerfull NRF52.
In this context we would like to use some of the new API’s that has been introduced...
Recompile dfu_dual_bank_ble_s132_pca10040 example from SDK v11 with softdevice v3.0 header. DFU is advertised, but not able to connect to it. always timeout,
There are three...
I made a product with nrf51822AC(based on SDK6.1&softdevice7.3), now we want to do BQB testing and I am working on our board's DTM code.
I have tried example "\Nordic\nrf51822...
Hi Nodic:
I use the PCA10028 V1.2.0 board , and use "nRF51_SDK_9.0.0_2e23562" SDK, ..nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_uart\pca10028\s110\arm5_no_packs...
Hi,
In SDK11 I was able to update advertised device name without restart, just handled write on the characteristic and update advertising data (through a second call to...
I'm going through pin_change_int example and can't understand how we tell controller where locate the function for our event.
Probably it occures in channel_port_alloc that...
I'm trying to communicate with an EEPROM chip using SPI. When I run under the debugger, the EEPROM doesn't respond; without the debugger running, it seems to work fine.
...
Hi everyone
I am working with nrf51822 sd 110 v.7.1
If I change from XXAA to XXAC, do I have to change the IRAM settings? If yes, which are the correct settings?
...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
