Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When I connected the development board with komoot (based on Android), komoot repeatedly disconnected again. The chip platform is nRF52832, and the protocol stack version...
Hi,
I try to rotate an image (180) with nrf_gfx_rotation_set(p_lcd, NRF_LCD_ROTATE_180). This only works once, but after, I want to return to the original position by re...
Hello
I am currently trying to get sensor values via SPI communication with mpu9250, a 9-axis sensor.
Although the following settings were made,acceleration,gyro,and...
Hi Sir,
I am going to the same phenomenon as below.
https://devzone.nordicsemi.com/f/nordic-q-a/45554/sdk-15-2-how-to-set-a-value-to-a-hid-feature-report
Can someone...
Eventually we got it working with the Master Control Panel again, but it will not work with our test software. I suspect a Window update change that affected links. Window7...
Hello,
I would like to implement a design using both the ESP32 Wi-Fi as well as the nRF52840 on the same PCB. As they both operate on the same 2.4GHz frequency and the antennas...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from mobile but iam able to send 1 byte...
Hello, I have 2 custom service running each with one characteristic. When data is written to the characteristic one (io_controle.c) the write event is triggered twice. The...
Hi,
did anybody find a suitable and cheap enclosure for the nRF51 Dongle? I want to use some of the dongles for initial tests before producing my own boards.
Thanks...
Hello, I have modified the example from the light switch on the mesh SDK and I can send and receive string messages, but the problem is that it doesn't work as expected, because...
I (unfortunately) had to make my own forks of Zephyr and NRF to get around a build issue, and decided to implement a west.yml manifest in my application repository. I made...
A makefile project using SDK 15.0.0 that compiled under GCC 7.2.1 no longer compiles under 7.3.1 with these errors:
../../../../../../external/segger_rtt/SEGGER_RTT_Syscalls_GCC...
Hi
I am trying to run the light_switch example, following the steps provided in this link . I have one Development board and 2 custom boards. It asks for Segger IDs for...
Section '5.2.1.1 Sleep' of the nRF9160 Production Specification v1.0 identifies SLEEP power with no RAM retention. My application will require partial RAM retention during...
