Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear SOC developpers,
As many kickstarters i bought an RFDUINO kit, then I made a cool prototype thanks to the easy Arduino compatibility. I'm now thinking of industrializing...
Is there a simple software code example how to configure an interrupt handler for a single GPIO-pin? I am using nRF51822 chip with softdevice S110 and the interrupt source...
My question a little weird. Because I am super beginner about BLE. So what I want is how to write string data. now i am looking to information about this. I cannot find it...
Hi
I'm trying to implement bonding in a device based on the S120. As counter part i've used a S110 device or an iOS device (realized with LightBlue App).
While searching...
Hi All,
I am using nRF51422 and now doing ANT+ certification test with tool v1.3.6. And i find out some problem with the received value on my display in case of following...
Hi
i am not able write my application after I flashed the SD. I am using Jlinker lite (the one that comes with the Dev kit) and the scripts from the nrf pure gcc . I modified...
Hi everyone,
Is it possible to connect 2 devices simultaneously with the nRF51822 device? As soon i connect one device, the advertisement stops.
So, for me it would be...
I've already posted my problem here. But it seems a dead thread.
devzone.nordicsemi.com/.../nrf51822-timer-problems
I ran into trouble when using the app_scheduler without...
Hi, I've been trying to use the timers on nRF51822 but I just can't get them to work in my code. When debugging (with GDB and Eclipse), the execution always stops with the...
Hello.
I've asked a question a while ago, devzone.nordicsemi.com/.../sd_flash_page_erase-failing-with-s120
I've been using Linux, jlinkexe, and gcc that time. Now I...
I just got the new Nordic "mbed" dev board and have started experimenting with it.
In another thread it is explained that the softdevice is bundled into the generated ...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Hi Dev Team,
Please guide me that, What is the data format needs to follow between BLE profile and iPad in order to transfer data.
I am performing both update(read) and...
Hi,
We have an extra current of 1uA while in system off mode(no RAMS). we get ~1.6uA instead of 0.6uA as we read on SPEC.
Do you have an idea what may cause the extra 1uA...
