Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
Hi
I use MT8852BE to test nRF54L15-DK ,TX power setting 8dBm but MT8852BE Power(Pavg) show -6.07dBm ,Why is there such a discrepancy in the values?
nRF54L15-DK Setting...
For power cost down, use dts config to set pwm gpio H0D1 as follow:
pwm1_default: pwm1_default { group1 { psels = <NRF_PSEL(PWM_OUT1, 0, 26)>; nordic,drive-mode = <NRF_DRIVE_H0D1...
Hi,
We have defined a FOTA update for a set of devices. Our device SW follows the 'multi-service sample' code for FOTA.
Generally, FOTA works well for devices in a job...
Currently (as far as i can tell) the firmware for the DECT-NR+ mode is mutually exclusive with the LTE firmware, and you cannot mix the two wireless modes as you have to flash...
We use the device shadow "desired" section to send configuration params to the device. The device processes and accepts the params and then returns them in the "reported"...
HI
Based on the nRF54L15 with SDK 3.0.0 and MCUBOOT for OTA updates, I've discovered there's a firmware image compression algorithm available. However, when compiling with...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
When running the NRF Connect SDK SoftAP sample, connected stations disconnect at **exactly 5 minutes** (300 seconds) into the session, regardless of activity or configuration...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
My SPI slave sensor requires a 32-bit frame length. The CS (Chip Select) signal needs to be switched for each 32-bit frame interval, and it also supports DMA (Direct Memory...
Hi ,
I am using skb501 module and which contains nrf52840.I am using nrf5sdk for development for zigbee coordinator because nrf connect sdk is not supportable in this...
Hello!
We are developing a device based on the nRF5340 and using SDK v2.6.0. The firmware implements a USB composite device (CDC ACM + MIDI + Audio). Everything works perfectly...
I am attempting to interface a tas2110 with an nrf52840. I just became aware of some nrf52 limitations and wanted to get the latest info. My requirements are as follows "The...
