Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hello,
I want to use multiple timer interrupts, want to fetch values from 3 analog pins on every 20secs and then average three collected values at every 60 sec. so i would...
Hi currently I am handling a project in which I used nRF51822. I am using SDK 11 and softdevice SD130. I want to know is there any significant difference in power consumption...
How do I rename the Solution/Project from template_pca10040 to insert_name ?
I copy-pasted the template_project folder and renamed it
I changed the names in [SDK]\[SDK...
I have a nrf52 DK that I want to use to program the nrf52832 IC. I have bought a qfn48 adapter from here . I wish to use this adapter to place the IC then make connections...
Hi, all. I am in need of serious help. I need to set up a wireless mesh network using the nRF52840 SoC. It must have 9 nodes and be capable of multi-hopping. I need to set...
After configuring and enabling COMP, when READY event emits, is the RESULT register valid? Rephrasing the question: must you trigger the SAMPLE task to ensure RESULT register...
Hi, I've rebuilt so far with the help of multilink examples, the uart example that I can connect to two devices (According to the status of connection-led and the debug info...
SDK:15.2 KeilC:525 SoftDevices:s140_nrf52_6.1.0_softdevice Hardware revisions: PCA10056
I have try the multiperipheral in 4 smart phone connection in blinky App. But I need...
Using nrf52832, SDK12.30 demo project ble_app_uart, testing with nRFconnect app.
Load ble_app_uart demo to board and run. Open nRFconnect on smartphone scan, and connect...
Hello,
I am encountering a small problem with my timer, I followed the tutorial : devzone.nordicsemi.com/.../application-timer-tutorial
The purpose of my project is to...
We have been using SDKv11.0.0 with S130 softdevice on nRF51822-QFAA rev 2 on a custom board with no problems at all.
Since our nRF51822 BLE module vendor no longer support...
Hi guys,
I flashed the mbr hex file and then the open bootloader to a custom nrf52840 board. When i first connect it, it boots into the bootloader mode and i am able to...
Hi,
I need to use
p_status->action == RELEASE_ACTION
to set the brightness level, but the p_status->action only gets updated after the loop finish so:
if (p_status...
Using the Border Router Quick Start Guide I've created the following setup.
2 Raspberry Pis, each with their own nRF5280-DK running RaspPi_OT_Border_Router_Demo_2.0.0...
Hello,
I am using nrf52840 with OpenThread stack. While I am using FDS to store application data, it seems the OpenThread dataset is written in the same area. Thus, the...
