Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hello
I have a very strange problem
A custom nRF52840 board has a charge detect pin, P1.6
A gpio callback is installed to wake it up on charger connect/disconnect
...
I was wondering if there was a way to use the Nordic Power Profiler Kit II (PPK2) as an ampere meter, and be able to determine more details about what portion of the current...
Hi Noridc expert ,
I am trying to configure using nsib + mcuboot on nrf52840,
I need to build the image with only public key avaliable , and sign the image else where...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi all,
I have ublox nina modules including your nrf52833 .
I downaloaded the ublox application here:
Release C209 AoA Tag v2.0.1 · u-blox/c209-aoa-tag
and opened...
Hello! I've been trying to do the same project for about a month now - just a simple keyboard adapter that takes the input from a keyboard and translates it into HID signals...
Hi,
Is it possible to advertise legacy (without extended mode) and coded simultaneously, and both connectable?
I see the sample from nRF Connect SDK, multiple_adv_sets...
I’m writing BLE UART code. When BLE is not connected, current consumption is ~30 µA. But when BLE is connected, consumption increases by ~1 mA. I want to reduce the current...
Hiya,
I was testing with USBD MSC, using fatfs (exFAT) and was hoping to inquire about a reasonable expectation when it comes to transfer speed.
My current setup is as...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hello,
I’m trying to run the TensorFlow Lite Micro example (zephyr_samples/hello_world) on my nRF5340DK using nRF Connect SDK 2.6.1, but I’m unable to build the project...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Bluetooth connection cache processing - Nordic Q&A - Nordic DevZone - Nordic DevZone
Continuing from last time. After some optimization, the program was able to work. However...
