I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
Keywords: nrf52832, pwm_driver, two pwms, 6 channels, pwm in sequence
I have four LEDs: three mono white LEDs, one RGB LEDs(three color leds) that produce white...
Hi,
I use usb_msc in nRF5_SDK_15.3.0_59ac345 use case, format file system and create folder and its subfolder test, found that segger development environment compiled programs...
Hi
I have followed the all the instructions with regards to 'nRF9160 DK Getting Started' and all is fine until the stage "Building and testing a sample application" where...
Hi Team,
We need to enable the two crypto backends one is CC310 and mbed TLS at a time for our development purpose.
Why means one of our features used 128 bit AES ECB...
Hi, I need a little help with understanding to implement security in my application.
Most examples used by Nordic have public advertising on, so any device can connect to...
Hello I'm working with Zigbee Dimmable Bulb example. Testing environment is as followed:
nRF52840DK SmartThings Gateway SmartThings iOS app.
After changing the Zigbee...
Hi,
I am trying to connect the Thread Devices to the Internet with the following setup:
OTBR from GitHub (This is not Nordic's border router) running on a RPI4 with...
Hello,
for some reason, I have mistakenly entered in the NRF51 USB dongle bootloader mode, and cannot exit. I have read that it is possible to overwrite the DFU/bootloader...
HI,
I am building my application on one of the nordic ble_app in SDK 15.3.. currently, I am facing a strange issue. I am using fds to store some data on the flash. my write...
Hello,
I'm running into an issue after upgrading my SDK from nRF5 SDK v14.2.0 to nRF5 SDK v17.0.0 .
We are using NFC periodically, where emulation is started and stopped...
I'm using the NRF52832 BLE DFU bootloader to run my code (slightly modified from the secure DFU example). At the start of my application, I toggle a pin and measure this with...
Hello,
We are at initial stage of design proposal.
Could you please provide the clarification on following points?
1. nRF9160 SoC is interface with BLE chip nRF52480...
Hi everyone,
sadly one of my nRF51-DK boards seems to be terribly bricked.
During firmware update nRFgo Studio (on Windows) stopped responding. After a (long) while I...
I could successfully installed development environment.
Could import Blinky application and could successfully build.
But couldn't import asset tracking application...