Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Central and Peripheral are connected by BLE.
The following error may be displayed when sending BLE message multiple times to the peripheral at the same time.
>> NRF_ERROR_RESOURCES...
Hi,
I found a bug in fds module ( Flash Data Storage ) which lead to data system corruption.
Scenario:
Given the device started GC(Garbage Collection) procedure...
Hi,
I have found a bug in the fds module (Flash Data Storage), which lead to losing "installed pages". If it was a swap page, fds module will be bricked.
Tested on SDK...
Hi,
I have written a short driver for the ADXL362 accelerometer, which I'm attaching here, and I've connected breakout board of the accelerometer from Sparkfun to the nRF51...
Hi there,
I have just upgraded the SES to V4.16 and followed the assistant guide in nRF Connect. I have deleted the old ncs folder (and all files) and also created a new...
I measure 184 uA of current during WFE. I've read in other posts that the nRF52832 should draw about 1.2 uA during WFE.
I've looked over the project settings many times...
Greetings,
I am using nRF52840 Dongle and nRF Connect v3.2.0 PC application to scan for nearby Bluetooth devices and connect to them.
I want to develop a PC application...
Hi, I use in my design a component which use the nRF52840 - WLCSP package.
I use SPI to connect the nRF to a SD card slot. With the package, I understand that pin K4 (P0...
Hi all,
I am debugging the data transition flow of the Node with Relay.
We modified the example of ONOFF_server. We found that the unicast address should the odd number...
Hi, I cannot find my Nordic Thingy91 as a USB connected device in the nRFConnect desktop application.
I tried to connect the Thingy via a JTAG 10-pin cable via an external...
Hi,
Greetings!
I am trying test DFU example for nRF52832 and I need help to move ahead.
Setup:
nRF52832 SDK for Mesh V3.1.0
nRFSDK V15.3.0
nRF52832 Development...
Dear all,
I just played around with the nRF Sniffer and I am pretty impressed. Really good tool and most of the packets are received.
I want to build an application where...
I have reprogrammed the nRF52840 board controller. When I run the lte_ble_gateway application I get the following on the 2nd dev kit VCP port:
SPM: NS image at 0xc000...
hello, i have a question, i use sdk15.3 for nRF52832, i run for example flash_fds, sometimes it will not be able to erase or write to memory, after restarting the device,...
I'm having a problem that I get some presumable interference between a high flash memory activity and UART communication. I'm writing single words into flash quite often,...
