I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
First time posting, Here are the details of my setup, I would greatly appreciate any help from anyone at this point. I have purchased 2 nrf52 development kits with...
Dear Sir:
I use ble_app_uart example , i want use pwm to driver the FR Port ,Peripheral load. the Peripheral load is pulled up to battery.
when driver the load ,the...
Hi All;
Just a major concern of mine is that SES IDE is so inconsistent;
I can build a solution get errors and warnings...
Without editing anything and rebuilding the...
I have an issue with my board. It resets occassionally itself. When the board is starting by debugger and when it resets itself I can read 0xD in RESETREAS register. What...
hi,
I tried to provision the light example using the nRF Mesh app.
So far, I succedded in provisionning the device but i couldn't set the publish suscribed addresses,...
Hi, I'm using a modified version of the light_switch example to control a RGB led on Mesh SDK 2.0.1. I already managed to control the led by using 3 variables for each color...
I'm designing a Printed Circuit Board (PCB) for and embedded system currently in development. I am using a BL652 DVK from Laird and using SWD programming with Keil uVision...
My project is using QT program and nRF52DK borad.
I want to UART communication with QT and nRF52DK.
#1. If i write "hello" in qt program like below...
===========...
I saw this post for SDK v12.2:
The FDS requires data to be word-aligned
devzone.nordicsemi.com/.../how-to-force-word-alignment-for-fds
Is that still true for...
Hi,
My target is to update the application firmware running on the nRF module using serial wire connection.
I currently do experience the issue, that DFU process completes...
I am in the initial phases of porting an arduino project using the NRF52832 to the Nordic SDK (14.2 for the moment) and am running into issues when using TWIM and an event...
Hello
Im trying to figure out where the health model client sends the health messages. Ive tried doing prints in all of the send methods in health_model_client.c but not...
Hello,
I'm having an issue when I try to connect to my device from an iPhone X. I'm using SD132 v6.0.0 on SDK 15.
The phone tries to connect and then it times out. All...
Hi!
After connected and get log info "Connected." I start bonding:
but there is no any success message.
Therefore nRF52 SDK15 can't to made secure bond.
Why?
