Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi, I am trying to create a custom board and add it to the zephyr app. Currently, I have added boards/arm/irnas_izoramv21 file to my application folder. When I am building...
Hi
I am using nRF51822, S130, SDK12, Working on adding static key security to my application
So far I have change the GLS (glucose) example to static passkey and connected...
I am creating a peripheral and central. The peripheral is done and appears to work fine. The central is in progress. It will use the serial port to communicate with a host...
I'm using the nordic SDK since version 8 (now version 16). For various reasons I always tried to not use the SDK and just programmed against the soft device API and programmed...
Hi,
I am implementing PPPoS using LwIP + FreeRTOS on nRF52840.
I have added LwIP and FreeRTOS which is available in " SDK/external/ " folder.
In LwIP I used LwIP's Sockets...
Hi,
I am trying to use nRF Connect for desktop with a dongle or nrf52 DK to connect with another board. When I want to get the value from the connected board, it would always...
We have a custom board based on the nrf52, We trying to integrate BLE functionality into our already existing firmware. I am able to create a custom service and characteristic...
ret is declared inside a "CRITICAL_REGION" which is a block, so not accessible outside that block to return: ret_code_t app_usbd_hid_generic_idle_report_set(app_usbd_hid_generic_t...
Hello, trying to make the leeap from nRFGo studio to nRFConnect, programming tool. I have connected to an old device programmed with nRFGo, and see the memory map below. I...
I am trying to debug an app error in my code. I have an app_error_fault_handler that starts like this:
But, the "Fatal Error in file..." line doesn't show the file...
DFU over serial
- Application alone - works
- Softdevice + bootloader works, but then doesn't respond to ping when trying to send Application image next
nRF52832 ...
Hello,
If the locators have AoA direction finding support ( nRF52833, nRF52833, nRF52820 etc , ) does beacon device require to have direction finding capabilities as well...
hello ,
I am using NRF52840 for my application, ESP32 as central and my nrf52840 as a peripheral . central always connected with peripheral. i can send data through central...
To the kind attention of Nordic support team,
I have been reading https://infocenter.nordicsemi.com/pdf/nRF52833_PS_v1.0.pdf product specification, where only
aQFN 73...
