before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I'm using nrf51 without ble.
I want to update flash but not want to delete PAGE every time.
NRF_NVMC->ERASEPAGE = (uint32_t) page_address;
How can i do?
We use IOS DFU toolbox to upgrade firmware with BLE device. we can upgrade successfully with Android, but always failed with IOS.
wrong code is: DFUErrorReadingVersionFailed...
Hi, it's probably a very dumb question, but i don't seem to find any details about it. In nrf52 SDK documentation, in Error Module section it says
The behavior of the...
Hi friends...!
I want to put dynamically changing MPU data into the advertising packet. I am putting my accelerometer data into manufacturer specific data field of ble_advdata_t...
How robust is the output PA of the nrf905?
Assume the ouput matching network and 50Ohm connector is used as in the 868Mhz application note.
If the antenna is removed...
Hi,
I'm trying to find a way to speedup the upload procedure of an application, via BLE on a Arduino Primo with the DFU service.
Here you can find my code:
https://github...
Hi,
I am using ble_app_uart sample code for testing. In that I want to store the incoming data into to three buffers and simultaneously sending this over BLE. i.e., consider...
hi i m using nrf52832 for detection acceleration , angular speed and detection of magetic field with GY-87 ( MPU 6050 and Hmc5883). in fact i wrote a program that read only...
Hi,
I am using s130v2 and running the example code from: nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_hrs\pca10028\s130\arm4
This is the only modification I...
Hi,
I know this is a Bluetooth 5 spec question, but wanted to know the practical figures for current consumption when nrf52840 is used as both central and peripheral...
Hi,
We are expecting many of our devices to be in close proximity. How can we be certain that when a user initiates a buttonless DFU, that they are uploading to the correct...
Hi,
I thought central is the one which fills up its look up table with 16 bit IDs to keep track of the peripherals. If multiple devices can act as central at the same time...
I am trying to re-base my SDK package, and when I started off with the ble_app_template project for the pca10040 s132, I copied my main file on top, everything compiles just...
I am developing an application which involves control of a brushed DC motor with a quadrature encoder. According to this post, in SDK 12.2.0 - which I am using - it is possible...
