Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I am working on nrf52840 and also the dongle by segger. My data is transmitted via BLE sucessfully but I can only see the results in figure but I can't save and process the...
Hello everybody,
I have programmed the example light_switch (server) and (client) from SDK for Mesh examples on two nrf52840 dongle and it worked .. I can control the LED...
Hello,
I'm currently trying to implement a setup of BLE devices (nRF52 DK and nRF52840 DK) which is potentially secure against the KNOB attack (and also other attacks) and...
Hi, I am looking to use the nrf power profiler to analyse power consumption with some configurations on the NRF52833.
I currently have the dev board PCA10100 and the power...
I was looking for more information about hardware accelerated AES128 functions in the nRF9160. We want to encrypt and decrypt data using this and was wondering if there are...
Hello,
I am currently working on adding the pairing part to the ble_app_uart with peer manager. I have followed the way that is used for ble_app_gls and ble_app_hrs. I could...
Hi support team,
I download mesh (nrf5_SDK_for_Mesh_v3.2.0) serial example FW to nRF52840 DK,
and connect to embedded linux gateway over USB,
I can run PyACI example...
Hi,
It seems that s112 soft device uses IRQ level 0,1,4 of nRF52832.
By default my counter has default IRQ level 6, my concern is about the delay of COMPARE interrupt...
Hi, Everyone
Environment: SDK15.3, nRF52840, Keil Compiler
I want to keep the previously set values undeleted even after OTA
My question is
1) Which method is better...
from this guide
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h23sjziacp7vrw0scs2t3tua1ax0426
It is...
Good evening.....
I am looking to play around with the Thingy 91 but I am a hardware guy who knows enough about firmware to be dangerous. I typically run into issues getting...
Hi,
I am trying to send firmware image from one board to another board. For that I want to use DFU control point characteristics.
I am using nrf52832 development kit...
I have installed the cocoapod for nrfMeshProvision, but i am new to BLE technology. I am able to fetch the dataIn and dataOut characteristics, but stuck at creating a Proxyhandler...
Hi,
I have a project where we want to setup 3 PWM channels for dimming LED strings in a mesh configuration. So the mesh dimming server is a perfect starting point. I did...
