I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello Everyone,
I'm involved in a project where we are evaluating ble mesh and Thread mesh on nrf52840.
I want to know, does Nordic supports ble mesh and Thread mesh simultaneously...
When using Keil Compiler, I am unable to compile any of the ble_peripheral examples. I get an error that says...
RTE\Device\nRF52832_xxAA\system_nrf52.c(29): error: #5...
Issue with NRF52832 Firmware installation
Hi We are developing custom boards with nrf52832 chip, and it is working well.
The issues occurs when installing firmware without...
Hi,
as i mention in https://devzone.nordicsemi.com/f/nordic-q-a/44924/dfu-serial-failed i have f ramming error now and then when i do DFU over serial.
My idea was to write...
Hi,
after I received the thingy91 I wanted to connect it to the cloud, as mentioned in the get started.
But when I want to add the LTE Device, it shows the following Error...
Hi,
I got a new USB840M that have only the NRF52840 with a USB connector, I installed the nordic_cdc_acm.inf (driver for USB) for my PC, and my PC started to recognize...
Hello
I'm using the Development kit nRF52840, SDK 15.3.0, and the Sofdevice s140 6.1.1
I've created a BLE Battery client service, my implementation is extended upon the...
Hi Nordic DevZone,
I am currently trying to implement a system whereby a nordic nRF52 board scans and broadcasts in alternation, using freeRTOS tasks.
I have yet to...
When I tried building the Mesh 3.2.0 SDK on MacOS with cmake, I got link errors with the static libraries rtt and uECC.
The fix I discovered was to change the CMakeLists...
I am working on developing an application where the app layer tries to throw out messages if the message parameters are not valid. One the parameters to validate is a TID...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Does following...
In order to compile against custom hardware, we changed overlay and dts files, but I cannot remember which. How do I find out?
I get the error
devicetree error: 'ss-pin...
I am using NRF52832 as Beacon, I want to classify the RSSI as High, Medium, Low, and Poor based on RSSI.
I am using SDK14.2.0 for Beacon and Gateway.
And using +4dBm Tx...
