I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hi, If I understand correctly the debugger on PCA10040 can operate in 6MHz/n as SWO frequency.
the nrf52 can operate at 4,8,16,32MHz swo frequency.
How are we to use SWO...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I'm trying to implement the DFU Feature into my application, but it seems to be in a bootloop after it starts advertising.
The application works fine when flashing it via...
Hello everyone, I want to measure Low power mode current consumption in nRF52 DK,but I dont have accurate CRO to measure in micro Amperes, therefore I would like to know if...
the eclipse build memory map is
text data bss dec hex filename
363312 2485 5340 371137 5a9c1 ********.elf
363312 2485 5340 371137 5a9c1 (TOTALS)
it is giving very large...
Hi Friends, I like Nordic and Arduino, it's great if Nordic can support Arduino officially, we can use the ARM0 in Nrf51822 as a single control point of Arduino project. There...
I taken the Android-nRF-Beacon-for-Eddystone app code from github.
From my account I configured my Google Dev console:
enabled proximity API
added credentials...
Hi all,
I followed the tutorial listed below:
devzone.nordicsemi.com/.../
I want to use SEGGER_RTT_printf but I always get this error:
Error: L6218E: Undefined symbol...
Hi,
I am working on one project in which I want to connect my two custom borads with S130 softdevice but I am not able to do that. My custom board has nRF51822 chipset...
I would like to implement a simple code to use SAADC on NRF52 to sample one channel at maximum sample rate (theoretical 200KHz).
All the examples I have found use limiting...
Hello All,
At a time either ble nus or dfu can work.
I have an problem with the services ble nus for uart and dfu does not work simultaneously means if i am adding both...
Hey, I got 2 beacons which I have connected via BLE successfully however I have some problems with BLE_GATTC_EVT_HVX event. Every time I get only one BLE_GATTC_EVT_HVX event...
Hello,
I measured the current consumption at 0 dbm of the app beacon example.
During the TX send phase I measure a current of more than 11 mA. Thats too high when I compare...
