Hi,
I am using an nRF54L15 and I would like to explicitly enable the HFCLK (32MHz). I want to use it to drive TIMER00, which will run during the whole application runtime...
Hi all,
I am working on a project that requires me to run the SHAKE128 and SHAKE256 algorithms as specified in FIPS 203. I am wondering if it is possible to implement these...
Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Hi,
I see the different behavior of the function sd_ble_gap_conn_param_update when connected to Windows integrated Bluetooth.
Using bare-metal SDK v0.9.0 it succeeds...
Hello Team,
We are evaluating an architecture where an NXP MIMXRT700 EVK powers an nRF9151 DK externally while using the nRF9151 DK as an LTE modem.
Hardware:
MIMXRT700...
Hello, We have registered our project with Nordic. Our project ID is 60803622472. Project title: DECT NR+ Star Topology Sensor Node Evaluation with nRF9151 We would like to...
Hi,
I'm using the S132 on the PCA10040 with the external XTAL disconnected (SB1 and SB2 cut)
In order to check to if the external is present I call nrf_sdh_enable_request...
I am working on my first BLE project for my employer and have been unable to connect over BLE to our custom board with the nRF52840 processor. To eliminate issues with my...
I received a nRF9160-DK and was looking at working with zephyr/boards/shields/x_nucleo_iks01a3 but my x_nucleo_iks01a3 shield will not plug into the nRF9160-DK (DK) it seems...
I have setup a small thread network (1 FTD Router, 1 Border Router, 2 MTD Dongles) using the Nordic provided RaspPi border router image.
I have been attempting to get Thread...
In my custome PCB design, I am using the CHIP antenna , the same used in nRF 9160 DK, that is P822601 from ethertroncis. Can this antenna work for GPS too? If not can you...
Hello,
I'm currently working on a custom DFU op-code that allows the MCU to send a "pause" op-code, similar to the op-codes found in the DFU protocol.
The steps I've taken...
Hi All
I’m making a few tests on a custom board equipped with a nRF51822-AA device trying to update the firmware with a newest one based on a more recent SDK
The original...
nRF5 SDK version 17.0.2
In usb_dfu_transport_init we have this:
If the nrf_drv_power driver was already initialized, this will return NRF_ERROR_MODULE_ALREADY_INITIALIZED...
The documentation for the sd_ble_gatts_hvx() method states:
This function checks for the relevant Client Characteristic Configuration descriptor value to verify that the...
Using NCS v1.4.99-dev1.
I have no problem using the PWM with a nRF5340PDK but when i tried it on a nRF5340DK, my program was not working correctly.
I have made a simple...
Hi All:
As the topic............Now ,my program is consisted two group,one is the base group,the other is the application group.We often upgrade the application group,so...
Hi
Try to enable reset pin on a 52810 custom board
After defining CONFIG_GPIO_AS_PINRESET in project I ended with UICR registers set to 0 both PSELRESET[0] and PSELRESET...
