Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hello all,
I am having issues with the configuration of the FEM nRF21540 on the costum board Fanstel BT840NE with the Enhanced ShockBurst (ESB) protocole.
We are not able...
We've got a sensor board with an nrf9160 on it, that sleeps lots of the time and periodically wakes up to take sensor readings or send them up to the cloud.
Some of the...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
i have question about nRF52832's bluetuth. xtal is 32M, Cload is 12pf, but the frequency is 2.402199G(tested by Network Analyzer), Frequency differency is 199K. We find that...
Yes I've already looked at the following two examples:
https://devzone.nordicsemi.com/question/185381/disabling-pin-21-of-nrf52832/
https://devzone.nordicsemi.com/question...
I'm currently working on a board diagnostic firmware and an accompanying Windows console app. The Win part of the project is supposed to monitor the diagnostic firmware's...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.0 on total 3 boards(1-client and 2-servers). I changed the no. of servers as mentioned in...
Hi All:
i want to change mesh net key to apply different client.
but when i change net key to {0x5f, 0x5f, 0x6e, 0x6f, 0x72, 0x64, 0x69, 0x63, 0x5f, 0x5f, 0x73, 0x65,...
Hello,
I ran light switch example on nordic boards & i am able to send light turn on/off command from client switch but i also want to configure my light servers to able...
I am using nrf_drv_uart library.
UART communication is set in non-blocing mode, and transfer od data is relised with nrf_drv_uart_rx and nrf_drv_uart_tx functions.
I am...
I am trying to run pb remote example but i'm stuck at command 3 it only shows "Got event 0" not goes further to receive remote uuid.
0> 1) Provision first available device...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
The printf statement is output to the terminal (Teraterm) using the UART. However...
Hello,
Our company is considering on developing BLE products with Bluetooth 5.0 compliance in mind. I'm currently trying to get as many information as possible but I'm...
Hi,
Once applying 0V to DEC2 pin, CPU hangs up and cannot be system resetted even though we input reset signal to RESET pin.
The only way to reset is to suppress system...
I am new to Nordic and BLE mesh connectivity. I have the following assumptions & queries, Please clarify if I am wrong.
1. Is it possible to implement BLE Mesh using Thing52...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
The wake on GPIO is working all the time now.
Unfortunately, I want to disable it except when needed.
Here is the scenario:
Power up, pushbutton pin senses clicks...
