Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
i have the nrf5833 dk board, i just started programming from quick start and it worked two times and now it does not program at all, programming failed
I'm seeing garbled/malformed UART console output when running apps on the Thingy:91 X. This includes pre-built apps from Nordic and custom apps I build myself.
Here's an...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
I have successfully connected an MCP3004 to the nRF52832 and can assign the ADC channel 0 output to a characteristic value. Works beautifully.
However, there are...
Hello,
I would like to know what are possibilities for low power in a central device on nRF52 chip.
I need to be in BLe connection mode, and be able to receive notification...
I'm trying to figure out if the NRF51822 is capable of performing the tasks I need for my project. I need to be able to do the following
4x PWM at ~2kHz
4x Analog read...
I am building a Bluetooth Mesh project and when trying to make a custom Makefile for the Mesh Light Control Example , but when compiling the project i get this error:
Compiling...
!!! (Distributor is unknown to me, but I can get it if needed)
Hello,
We are developing a BLE enabled device to operate on iOS and Android phones.
The nRF52832 chip...
Hi friends,
I'm using a NRF51 IC with this 4.0BLE Modul PTR5518 and i have big problems with Range. As a protocoll i use gazell.
In air it is possible do get some correct...
Hello,
I am currently trying to make an MSD RAM disk with nrf52840 nRF5_SDK_14.0.0 with O0 optimization level. And had no success. For some reason in Keil example O3 is...
Hello every one,
So after I made my 3rd party NRF52832 board and flashed softdevice S132 with arduin ide and ST link V2 I'd like to migrate to something more serious in...
Hi,
Do you know how to make the nodes in the Mesh send back the data to the main device?
For example, a node is a sensor that gets a new value and now needs to send the...
Would like to get continuous advertising data from a known device ID - without connecting. Would like to do this on a Windows PC. I don't see a way to do this with nRF Connect...
Hello,
We are working with the one potential customer . they are working on battery connected beacon project below are the some queries
customer using nrf51822...
i am compiling an code just to store a data to flash and retrieve it. i wrote the code for that i included fstorage.h,section_vars.h and added fstorage.c. I am not using any...
Hi,
In nRF5 SDK v14, in the file ble_advdata.h, there is a routine to create advertisement data from a ble_advdata_t struct that is passed. This struct allows only 1 manufacturer...
This omission leads to linker errors:
_build/app/nrf_ble_gatts_c.c.o: In function `nrf_ble_gatts_c_on_db_disc_evt':
nRF5_SDK/components/ble/ble_services/experimental_gatts_c...
