Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
Hi, I have a Nordic nRF52 Development Kit. The ADC examples work, the LED examples work, and the NFC examples work. However, none of the Bluetooth examples work. The LEDs...
My DevKit arrived today. Very nice.
Plugged it into my mac, immediately recognized as USB device. Flashing LED, mounted as storage device, etc.
Tried to enter Bootloader...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello everyone
I am trying to configure the write values like in the link loss profile it is possible to write no alert, mild alert, high alert, similarly i have created...
Hello!
I would like to know if it is possible to send an unique Gatt message that contains notification enable for multiple characteristics.
For example,
buf[0] ...
Hi Nordic,
I posted the issue with BSP package in devzone.nordicsemi.com/.../
unable to attach the main.c file mainOriginal.c
HI Aryan,
Thanks for your reply. Its working...
main.c HI Nordic,
I don't want bsp.c in my project. So I removed the bsp.c and included custom_board as mentioned in devzone.nordicsemi.com/.../
I am also using UART for...
I have the nRF52 dev board "PCA10040".
I downloaded "nRF52_SDK_0.9.1_3639cc9" SDK.
I noticed that there is no installer for the SDK.
I unzipped the SDK and using Keil...
Hi all,
Since I will use broadcast way in RF transactions between one NRF24LE1 based senders and serveral NRF24LE1 based receivers . I was told not to use "Auto ACK" in broadcast...
I'm new to Bluetooth LE, Python and C. I have the S130 python examples for heart rate testing. I am attempting to modify the heart rate collector code to act as our central...
I am able to use pstorage_clear and pstorage_load without any problems, but whenever I try to do a pstorage_store the callback function is not being invoked. This problem...
-Essentially I want to do a device firmware update on to the nrf51422 using my Android phone (the nrf applicaiton). I am using your sample code for a project that my company...
