I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
I referenced the question in this link devzone.nordicsemi.com/.../sd_ble_gattc_primary_services_discover .
And I can see the Read by Group Type Request and response in sniffer...
HI,
I add a readable and writeable characteristic with :
attr_md.vloc = BLE_GATTS_VLOC_USER;
attr_md.vlen = 1;
attr_md.wr_auth = 1;
and
attr_char_value.p_attr_md...
Hi Guys,
I'm doing a test between CC2541 and Nordic NRF51822. The CC2541 work as a peripheral role. NRF51822 as central role. But CC2541 can update another CC2541 that...
I'm working on a design that requires an adc reading to be taken on a pin that is also used as an interrupt. I've looked at the reference manual but am still confused as to...
The end of memory bss is @ 0x20002DAC (11692B).
The start of the heap is @ 0x20002DB0 with a size of 2560B.
The heap ends at 0x200037B0.
The stack works back from the end...
Hi,
I intend to buy the NRF51822 beacon to use it to transmit data from an SPI-linked sensor. Is this feasible? (It seems so, but I just want to make sure). Also, will I...
Yesterday was the nrf Beacon application for Andriod Studio released. I added the project DFU library to the same folder as described. But I get an error:
Gradle 'Android...
Hello! I want to try IPV6 for nrf51822. I have a few questions:
How many connections can be provided by the one device?
Can we broadcast messages between devices...
Hi,
I'm developing BLE functions using nRF51822 on top of the Android Kitkat applied device. I cannot find android bluetooth HAL source code that Nordic provides. Is there...
In my application I have a custom board with a single LED. While advertising the LED blinks at 1Hz and when connected the LED goes solid. However while testing with a proven...
I'm creating an application based on the s110 SoftDevice found in nRF51_SDK_8.0.0_5fc2c3a. I'm new to the SoftDevice framework so I've probably made an error somewhere but...
Is the GPIO pull down/up asserted on the 'inside' of the input disconnect switch or at the input/output pad? The diagrams would indicated that it is on the 'inside' of the...
This is function definition:
static uint32_t battery_level_char_add(ble_bas_t * p_bas, const ble_bas_init_t * p_bas_init)
This is declaration of the automatic variable...
Before starting advertising, we want to write some configuration information to NVM. In order to write to NVM, we first call sd_flash_page_erase and wait for the response...
