Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, I have a very odd problem but one which is consistent. As part of my lcd library I send several ''packets' of data interleaved with spacing from a timer. It typically...
Hi,
I am developing using nRF52820 / SDK 17.0.2
In order to store data in FDS, the handlers were registered and initialized as follows.
FDS_Event_handler does...
Hi.
I am working on nRF52832. I want to store a structure with 492kb I am getting heap is too large error. So how can I tell the complier to store my variable in flash instead...
Hello,
I am using nrf52_DK to debug PDM with a digital MIC, and select the pin 29 for the PDM CLK, But I haven't seen any clock signal output, for generating the clock...
I am develop a android application with BLE.
My bluetooth device can be searched by bluetooth scanning of android.
And my application can connect with the bluetooth device...
Hi,
My system is
- nRF5340 custom board - Zephyr OS build v2.3.0-rc1-ncs1 - nRF-Connect-SDK v1.2.0
To perform DFU over UART I was told to merge MCUBoot + mcumgr +...
Hi,
I am developing an application that needs to activate a relay on a central device when an event occurs on the peripheral device. The peripheral will always connect to...
Hey, Brand new to this but long time programmer and I sware I have been trying tons of stuff for 4 days straight now and only posting because I am out of options. My goal...
Hello!
I am new to the Nordic chips and for my project .My question is when i apply for the free SES license from license.segger.com/Nordic.cgi ,the The error is shown in...
Hello,
We have a GATT based product. It's using SDK16 and softdevice v7.0.1. It's using secure DFU to upgrade. Now we are developing new firmware based on Mesh 4.0.
We...
Hello, I designed custom board using nRF52832 and SHT20 ambient temperature sensor. Temperature sensor not detected using example sdk TWI scanner. SCL and SDA pins correctly...
Hello,
For our product, we wish to store a custom post-production name (essentially a serial number) in the UICR registers of the nRF52840. We understand that this can...
I am using a code similar to App_uart_C from SDK17.02 - central sending data over uart to another peripheral.
After 30-60 sec, the operation stops probably due to an error...
