Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
Device: nrf52840DK
Software: nRFgoStudio (version 1.21.2.10)
Operating System: Windows 10 (updated)
I am not able to enable the reset pin. I am trying to...
Hello All,
I am trying to build the "bootloader_secure_serial" example from SDK 14.2.0 on IAR Embedded Workbench IDE ARM- 7.60.1 and I get this error: Error[Pg004]: macro...
Hi,
I'm trying to utilize PPI system to generate repetitive sequence of tasks (lets call them Task A, B, C, D, E, F) at 0,10,20,40,60,80 ms every second. i.e. I need to...
Hi,
I'm trying to test adding my own custom service, but have errors when I tried to add a 128bit UUID, the test code is simple, in the service_init() function, I just added...
I am using nrf52832 and sdk 14.2.0.The software I am using is keil 5.17.the error is as follows:.\_build\nrf52832_xxaa.axf: Error: L6915E: Library reports error: __use_no_semihosting...
Hi,
In nRF SDK15, Bluetooth peripheral examples for HID devices were limited to keyboard and mouse. By any means, can we configure Nordic device as a game controller?
Hello,
I am currently learning the PWM peripheral of the nRF52DK and am a total beginner in PWM.
I have tried running the attached program and this allows the LED0 to...
Hello,
I am working on a project which requires radio transmitter and receiver to work in sync with the SPI. So the setup is as follows the Transmitter transmits a signal...
Hi,
I am trying to write my own dfu updater for the NRF51 chip and I am stuck trying to make sense of the actual DFU sequence described here infocenter.nordicsemi.com/index...
I am trying to set up mqtt between 2 nrf52s and rpi3 with the examples of sdk 15.0.2. I am very new to nrf52, rpi3 and networking. I have read everything needed as much as...
Let's send a string over UART. RTS signal will go low (active). So far, so good.
The problem is that RTS remains active even after sending is done. And because it is still...
I have two boards. I ran the exact same commands on both boards. The commands flash the same bootloader+app+softdevice+app settings hex file. One board reboots into the application...
Hello,
Setup: Running Ubuntu 18.04 inside Windows Host (using VMWare).
Device: nrf52840DK
Operating System (used for development): RIOT
I would like to communicate...
Hi,
I am running IoT LWM2m example. Everything were going fine since yesterday. when I do hcitool lescan, i see following output:
hcitool lescan LE Scan ... 28:45:8B...
I am using the ble_blinky example (s132) and want to increase the number of characteristics. I get the error code 4. I think the storage capacity is not the reason why I can...
