Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I am trying to transfer data from a USB to serial converter board (called board A) to the nrf5 board (called board B). I made the connection over a bread board, the transmitter...
hi i'm use nrf52dk
and segger embedded studio
also i'm mcu beginner
The value was obtained using a magnetic sensor.
now i want using the ble
Now we want to send...
Hi,
I started working with nRF9160 and took AT_Client and added support for my own commands. Additional to that I added HTTP example to it and they are working great together...
Hello,
i have a very easy goal, i want to generate a hex file which combines all parts and flash it via nrfutil or something like that onto the device.
I followed a few...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hey , i'm using nrf52832 with SDK 14.2 . I'm trying to send 3-axis accelerometer data through BLE . Is there any example for SDK 14.2 to achieve this ?
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As shown in below snapshot I am just doing below...
According to the blog below, hardware design of nRF9160-SICA has been fixed on May 31st. https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf9160-development...
I am designing a pcb just the nRF 52840 MCU. The design of the PCB is based on the reference design from Nordic. When ordering the PCB I came across a problem that the vias...
I have 4 gpio inputs on the nRF52840 working and sending these states over the BLE. I tried to add a few more gpio inputs but I get an error =4 which I think is NRF_ERROR_NO_MEM...
Hello,
I can successfully put my nRF52832 into System OFF mode, however, the Debug Mode Interface is still running, so the current consumption is > 2mA. What are the command...
I have a nRF9160 DK need to update modem firmware to v1.0.0
According to C:\nRF91\mfwnrf9160100\README.txt below, I should use nRF Connect Programmer to update modem firmware...
In the light_switch example of nRF5_SDK_for_Mesh_3.1.0, I noticed that generic_onoff_client.h has a union for holding the current message packet. However, there is only one...
The timer example with SDK 15.0.0 uses the old timer driver. Is there any example code showing how to use the current nrfx_timer?
I'm just trying to generate a periodic...
Hi Nordic team and fellow fans,
I am trying to switch from SPI to SPIM and getting an odd assertion with no context after I kick off a SPI operation, but it only happens...
