hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
We are in progrees of developing a wearable device using NRF52832 with BLE. The problem is, we have quite a few chips dead after several times of rewriting. The dead chips...
Hi,
I tried adding PWM for turning on/off the LED's on the DK for the Enocean switch example. It worked well.
I tried to perform dimming on the switch example by restricting...
Hello All,
This is a trivial question I guess but I am not able to figure out
Working on : nRF5 SDK for Mesh v2.2.0
SDK version : nRF5_SDK_15.0.0_a53641a
I have...
hello ,
can anyone tell me what shall i change in light_switch_client ( server ) to implement the simple_on_off model instead of generic_onoff_client ( server )
i started...
I am using nRF52840 for bluetooth mesh technology for industrial light control.Can anyone help me for my project, how can it be done,I have the light switch demo file, but...
Does any one use mtm m905 module. i tried this module and its a complete failure. the smt package is not standard and the BGA factory failed many times to solder this Module...
Dear Nordic Support Team,
I'm working on a BT Mesh implementation and came across a problem with the proxy enable / disable feature.
Disabling the proxy function doesn...
Hi all, I'm working on making mesh sdk work with peripheral uart example. I tried to merge peripheral uart example (nRF5_SDK_15.0.0_a53641a) into proxy_server example (Mesh...
Hi,
I was into the working of bluetooth mesh. I was wondering if it is possible to configure a bluetooth mesh network with a smart phone acting as a provisioner and by any...
My aim is to establish communication via nRF52840 dongles. This means if I connect mobile phones to the dongle and the data sent by one mobile phone should be received by...
Hi
Does the nRF52840 and 52832 support automatic gain control (AGC) for for BLE?
See this Ti post which suggests AGC is not used for BLE
http://e2e.ti.com/support...
I have recently migrated from SDK 15.0 to 15.2 and are experiencing problems with my code.
I have a nRF52840DK and have attached two accelerometers to this board. I am able...
Hi,
I'm currently working on achieving BLE NUS + ESB UART concurrent implementation via timeslot API, by referring to the example here . I have ported it to utilize SDK15...
Hello,
I'm using nRF5 SDK with version 15, nRF52832 IC and softdevice s132. I need to save hold the data in the ram even in sleep mode. I'm using the below code. However...
How can I return my nRF52840 DK to its out of box condition (firmware, demo) so that I can turn the device over to a colleague and let them run through the getting started...
