Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi,
We're producing a custom board based on the nrf51822 and would like to add a USB Serial chip.
The current contenders are:
a) FTDI 232R
b) ATmega8U2 ( www.arduino...
As the picture shows, I saw this softdevice_hex option available.
The error says, "require nRF_SoftDevice S310_Hex".
But where to this missing component.
My development...
Im sending an 8 bit int using my AVR controller as follows:
static uint8_t* dummy_heart_rate = 6;
aci_loop();
if (lib_aci_is_pipe_available(&aci_state, PIPE_UART_OVER_BTLE_UART_TX_TX...
Are there any pins that I can NOT use for SPI on the nRF51822? I'm not seeing any notes in the latest documentation but would like to make extra sure before I spin a board...
Hi there,
Using mbed i have currently programmed an nRF51 DK to transmit data through a custom service with 6 read only characteristics. Is there a simple way i can alter...
Hello.
I cannot get my head around app_timers. After reading the docs, examples and answers on the devzone I'm still unable to get it running. The timeout callback isn...
I am trying to add SPI to the ble_uart_example on my nRF51-DK but when I try to debug my code debugging just stops (All "step one line" etc. buttons grayed out) at this line...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
I am trying to do over-the-air (OTA) device firmware update (DFU) on a device with bootloader same to the "dfu_dual_bank_ble_s110" example in the latest nRF51 SDK . On the...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
We are using Gazell to stream data at <=6mS intervals for very low latency wireless gaming peripherals. We'd like to have many of these peripherals devices (more than 24)...
Hello
I'm trying to get a SPI master onto my S210 programmed nRF51422. I'm using uVision 5 and have all the nordic packs installed and built off of the ant broadcast tx...
