I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
Hi.
I am using nRF52840 Dongle. A problem occurred while merging the PIN_CHANGE_INT examples based on the BLE_APP_BEACON example. I connected the external button to the...
In the products that I am developing we use advertising packets in the scan response to pass some data around our devices. We wanted a way for the app we've made for iOS to...
Hi,
I am using nRF52840, S140 7.0.1. I am using ble_app_blinky application.
I am writing data into FDS records. After writing FDS, if I load new hex file using nrfjprog...
Dear all,
I'm trying to go to SYSTEMOFF mode and then wake up from activity on UART rx pin (nrf51822).
If I do this:
nrf_uart_txrx_pins_set(NRF_UART0,NRF_UART_PSEL_DISCONNECTED...
Hello, I have a BLE peripheral, that should receive larger amounts of data using a l2cap channel. The central (a MacBook) creates the L2CAP channel, the channel is purely...
Hello,
we develop an open source framework that we are currently extending to also support the BLE Mesh Access Layer Models. We are currently implementing the foundation...
I am using nrf52810, using sdk15.2, softdevice6.1.0, my application flash takes up 56KB (I used fds), softdevice: 100KB and bootloader: 24KB, resulting in insufficient flash...
Hi,
I'm try to test my nRF52833DK using the nRF connect Direst Test Mode. Even if I flash the DTM binaries in nRF5 SDK 16, the Direct Test Mode app says something like ...
Dear Sir.
I am using SPI as follows.
gpio_pin_write(dev_io, LIS2DH12_CS_PIN, false); err = spi_transceive(spi_dev1, &spi_cfg1, &tx, &rx); gpio_pin_write(dev_io, LIS2DH12_CS_PIN...
The firmware is based on the BLE UART example running on an nRF52832 with the S132 softdevice. The first batch of boards were build with the QFABB0 chip revision of the nRF52832...
I have set up APP_BLE_CONN_CFG_TAG with
#define APP_BLE_CONN_CFG_TAG 1
Setting things up in ble_stack_init exacly the way it is done in the example, but when I run sd_ble_gap_connect...
Hi,
I am using nRF52840 S140 V7.0.1. I have few queries on GPIO configurations.
Below are my PULLUP/PULLDOWN macros.
As per my understanding
1) In below settings...
