Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I have created a whitelist in nrf51822 device its working fine. But i stored whitelist details (pp_irk and pp_addr) to an external flash memory( bacause i not using peer manager...
I'm wondering if the extended advertisement feature of Bluetooth 5.0 is supported in any softdevice. If not, when can we expect it to be supported? Still within 2017 (as I...
Hi,
Each node has some state which should be saved in case of a power failure and recovered after it.
The problems:
how to detect the power failure?
where to save...
I have some Bluetooth LE v4.2 beacons that I will connect ONLY with known devices that we may call "readers". No consumer with use my beacons, I program them, I install them...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52840pdk.
I followed porting guide provided by InvenSense. However, I met the...
First of all, I know the difference between the two roles, and I have also read through docs.
My question is actually limited to the current nordic mesh implementation....
I need a bootloader that I can use for my application that doesn't use a soft device and allows the firmware to be transferred through uart. Going through the forums, I found...
Common situation:
We have flashed dfu bootloader, and firmware uploaded into Flash via DFU. In this situation, DFU settings page contains correct CRC value for existing...
Because if there is, I'm not seeing it. It seems to me that the SDKv14 has asks you where you want your event handler function like this:
Where spi_0_event_handler() is...
HI,
I have been trying to generate the hex files for the mesh sdk (Latest) examples using cmake following the instructions in the documentation.
But the platforms supported...
Hi All,
I am starting an application using nRF51822 beacon kit.
I have some observation regarding current consumption.
1- erase entire flash and power up only, i can...
I'm trying to measure the startup time of the 32 MHz XTAL at the pins XC1 and XC2. Often a microcontroller will indicate in a register that the XTAL and internal PLL are stable...
I wanna use NFC Tag module for OOB authentication in Bluetooth Pairing. I don't wanna use heavy SDK library for it.
Just need simple function which configure NFC to transfer...
I need to achieve the "few uAmps" level of sleep current while running the latest mbed-os 5 on an nRF2832 (inside a u-blox NINA-B1 module). I'm currently seeing ~500 uA in...
