Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I'm implementing a BLE Central based on S132 with functionality for getting a descriptor list from a connected device.
To avoid having to maintain a complete discovery...
Hello folks,
we setup a new Project (eclipse,SKD 12.2.0, S130, NRF51822QFAAH0) based on the sdk examples. But the thing since 2 days we got a error we actually do not understand...
I have a PCA10040 board and downloaded SDK 12.2.0.
I am trying to being a project based on experimental_ble_app_eddystone. I can compile and upload the code to the board...
Problem:
IAR compiled hex file does not work for ble_app_hrs
Environment used:
IAR Embedded Workbench for ARM 7.80 Kickstart evaluation
nRF52 DK
Observation...
Hello,
I use, with success, the FDS library to save data to the flash memory. I also use, with success, the bootloader to update the application (original dual bank ble...
Hello there, thanks so much for taking the time to read. My problem is the following
I am trying to run GZP (Gazell Pairing Library). After successfully pairing with a...
We are currently trying to log our sensor data to a mobile phone through uart using nrfLogger app. We have nrf51 module and we are using SDK 12.
In nrfconnect, we select...
Hi,
I have problem with long write by sd_ble_gattc_write.
I send first 18 bytes by button on pca10028, then I waiting for BLE_GATTC_EVT_WRITE_RSP and sending rest of bytes...
I need some help with something very basic...
I need a way to upgrade my DFU BLE bootloader to either reset back to the app if no update has been sent after some timeout...
hello,
According to the "twi_scanner" example from the SDK12.2 I don't understand how the respective I2C pins/GPIOs are set up.
There is this function that I found "nrf_gpio_cfg...
My nRF52 device is an asset tracker and does not have a comm port. I have been looking at a BLE dongle setup for manufacturing test but the results are not repeatable with...
HI,
Nordic part used is nRF51822.
Is there any way to increase signal strength of BLE tx?
I see some parameters in advertising_init function for advdata.p_tx_power_level...
Hi all
According to chapter 50.2 of the nRF52832 product specification V1.2, the pins used for the UART peripheral should be configured before in the GPIO peripheral to...
why most of the examples of sdk 12's sdk config file has different options?
I'm trying to build an application that has Central and Peripheral Role application (and it...
