This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
Hello,
I am using Nordic's iOS library to perform DFU in our app to upgrade firmware on some BLE devices. Before the DFU, the app scans it as "Paradevice", but reads it as...
Hi,
I'm designing a prototype board with the nRF52832-CIAA and was planning on using the Johanson 2450FM07A0035T integrated 2.4 GHz filter, but have not been able to find...
Hi
in pcb designing of the nrf52832 we use two oscillators one is 32 MHz and another one is 32 kHz.
can't we use both 32 kHz instead of one 32 MHz for saving power consumption...
Hi,
I can't seem to find an example for receiving an update about restored value of CCCD when a bonded peer reconnects. I'm using SDK14.
NUS and HRS examples which use...
I am new to Nordic, and Keil, and not especially strong in microprocessors yet. I am trying to get currently developed firmware for a nRF52382 chip to operate on a custom...
hi expert
i use sdk14.1 ,nrf58312, when my phone(andriod 5.2.1)connected to nrf58312 board ,i find the addr type is 2, so i want write the mac to whitelist ,but when i set...
Hi, I wondered if the source code of the SDK 51422 PCA10028's firmware is available ? The one firmware which allows the SDK to flash other nRF51X over the air? If it is, where...
While the default microphone mode on the Thingy52 is ADPCM - which I got working fine in my evaluation environment - the SPL mode defined in https://nordicsemiconductor.github...
Hi,
I am beginner for nRF52840. I use Keil uVision 5.20 to develop firmware. I have a problem with the Nordic packs downloaded from Keil website. The USB driver is not take...
Hello.
Until now, we work with NRF52832 for a new product but we have identified that the memory (64kB of RAM and 512kB of flash) of the chip will not sufficient for our...
Maximum connection node in 6lowpan over BLE
I am testing Pi to Nordic node (NRF52832 IoT Softdevice). When I test connection, maximum connection node is 10. Do you know...
Dear all,
Sorry for asking an old question but I can't find any similar situation in the forum. I now have 3 boards: 1 is 52810 EVB, 1 is 52810 QFAA ( 48 pins) custom made...
I bougth pca10056 and I need use it with Keil, but I do not find the pack installer for this board on "Pack Installer".
Furthermore, keil does not recognize my board.
...
I am using a lithium polymer 4.2V battery to power an nRF51822 (as a side note the power goes through a voltage regulator before going to Vdd). I want to be able to check...
When calling app_sched_event_put() no check is done whether the exact same record (same data, length and function pointer) already exists in the queue. We have setup where...
