Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
HI!
I use flash data storage (fds) to store some user inputs in flash. Everything works fine, but I am surprised by the fact that the function fds_record_update() is not...
Hi All,
Using SDK15.3, NRF52840 USB Dongle.
After a few experiments I would like to clarify my understanding on how the usb bulk write works.
I am currently writting...
I am using Nordic Thingy 91 Kit.
I have uploaded modem and application firmware URL : Nordic Thingy:91 - Downloads - nordicsemi.com
I am facing following problem while...
The following issue is for NCS version 1.4.0 and 1.4.1 for an nRF52840 DK target.
When CONFIG_BT_AUTO_PHY_UPDATE =y for both a peripheral and central, I see in Wireshark...
Hi,
I am using the following snippet in my application. it is working fine sometimes but the other times it's not coming out of the while loop.
can anybody point out the...
I have been struggling to reduce the current on the Nordic Dongle to the sub 3 uA levels that the specs suggest I should be able to achieve.
I am stuck at achieving a 9...
i am trying to determine the current consumption of the nRF9160 when in sleep mode but running LPUART and TWIS.
I see that the Sleep mode (MCU IDLE, MODEM off, RTC on) shows...
Hi all, i want to use CMSIS DSP library for vector/matrix computation.
In NRF connect SDK, there is a "nRF CMSIS DSP examples solution" in the dashboard, however it fails...
Hello,
I have an external flash w25n01gv, I am using this simple spi loopback example to test the spi functionality of nrf9160. I want to read the jedec id of my device...
Does doing DFU again and again on same controller can cause misbehavior of code? I am using BLE + UART + EEPROM in my code and sometimes I face the issue with UART event handler...
Hi,
I'm using NRF52840 to connect my mobile.
I'm using whitelist, following the example. It used to work perfectly for about 1 year.
However - in the last couple...
After starting the program, I do the first calibration and read the data 30 times. The standard deviation is between 2.0 and 2.3. Perform 30 "Calibration -> Read Data" each...
Hi,
Greetings of the day!
I used nRF Connect for desktop to program the nRF52840 device. But I can't lock the program and protect the device using this utility. I installed...
Hi,
I tried controlling the LEDs connected to P0.0, P0.7 & P0.11 by using
nrf_gpio_cfg_output(); nrf_gpio_pin_set();
nrf_gpio_pin_clear();
& ble_app_blinky example...
Hello,
My project application demands exchange the data from PC application(custom application developed by us) which is act as a server to the controller which is act as...
