Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Trying to compile ble_app_cscs example, but have compiling errors in ble_cscs.c library.
Anybody have any ideas what is wrong?
Ubuntu 16.04, NRF SDK 12.3, GCC 7.2.1
Terminal...
Hi all,
I need to send the information from 2-5 sensors in a room. The sensors are placed 2-3 meters far from each other. Each sensor has a BLE, using a battery and generates...
I'm using the RSCS demo as the peripheral and the Relay demo as the central. I've modified each to use stored bond information if it is found in flash upon startup. I make...
Hello.
I am measuring the current of nRF 52832 using PPK (PCA63511).
I want to measure the current of nrf chip only with PPK.
The chip of nRF is PCA10040.
What...
Hi all,
I've bought an iBeacon Station NRF51822 like this one ( linksprite.com/.../index.php5 . My idea is using it as a temp sensor for my smart home installation. It...
Hi Nordic,
I am getting started writing a new application and I would like to move to the new SDK14. My app requires, between others, a custom service and a custom characteristic...
Hello.
I'm tying to learn nrf51822. I had ordered some modules from ebay and nrf52-dk from local distributor . A week ago I had receive some modules. But local distributor...
hi,
My custom board running Mesh SDK0.92 send and receive messages are normal.But after I replaced the MeshSDK in my program with Mesh SDK1.0.0, I was unable to send and...
Hello all,
I would like to establish connection between single central and two peripherals for bidirectional communication. I edited ble_multilink_central example and created...
I and new to programming the BLE devices and have just started out on the nRF52840 PDK and using Segger Embedded Studio for ARM v3.34. I have compiled and downloaded the ble_app_template...
I have to question:
1: if customer use relay node for mesh net, how much is the power consumption for one node? is there any passable to declare the power consumption to...
Hi,
I need to measure the capacitance of few capacitors for which I am currently using 3-channel CAP1203 IC from microchip.
However, I just came across the possibility of...
Hello,
I would like to establish bidirectional communication between single central and two peripherals. I referred ble multilink central example and made corresponding changes...
