Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi. I am using nrf52832 SoC with s132 device (4.0.2). Device is acting as peripheral, I have set max BLE connection limit to 1. ble_cfg.gap_cfg.role_count_cfg.periph_role_count...
I'm following the migration guide from SDK 14.2 to SDK 15 , and am a little hung up on the new nRFx module.
All the examples in the new SDK use the legacy drivers but the...
I'm using the CR2032 to power up my nrf51822 with LDO setup, it works well in the begining. But when the voltage drops below 2.6V, my phone cannot scan the BLE. Is it little...
What is expected behaviour of s132 device (4.0.2) if peripheral is initialized with periph_role_count=1 and somebody tries to connect when BLE connection is already establsihed...
Hey Guys,
I'm a newbie on BLE development , I'm trying to run the example "examples\ble_peripheral\ble_app_ancs_c" , It works well first time, but it cannot receive the...
I'm using nrf52832 powerd by a 3.6V regulator in a li-ion powered application. And using one of the IOs (P0.05) as the power supply of other circuits.At the same time, using...
Hi
I am having trouble getting the basic BLE_APP_UART up and running. The UART printf() works, but the BLE module (NORDIC_UART) is not visible in all the devices android...
hi,
i am doing a project where i am using central and client model.
i am using nrf52840 as central device and thingy 52 as peripheral device and i am using sdk 14.2.0...
When using make flash on an SDK11 sketch, s132, pca10040, on Ubuntu 18.04, it successfully builds everything until app_uart.c; when it gets to that point, it outputs the following...
Hello,
I would like to test my code on a NRF52832-QFAB chip with 256kB chip to see whether my code fits into the 256kB flash variant.
According to nRF52832 Rev 1 Errata...
hello
i am using segger embedded studio. with nrf52840 and sdk15.
i was working to set the clock using nrf_clock_lf_cfg_t which is defined in nrf_sdm.h .
nrf_sdm.h is...
Dear Sir/Madam,
I am working on a 51822 project which send data to Android App. This project is actually an replacement to an old BLE sensor which is obsolete now. I have...
HI.
I use the peripheral example of SDK15 to implement functions such as uart, spi, and interrupt.
However, if soft device S140 is programmed, then my code is not programmed...
Hello, I am currently writing firmware using NRF52 SDK 11.0 (there are plans to port to SDK 15 eventually, but for now I need to get it running with 11) on Ubuntu 18.04. After...
