Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
After disconnecting from chip I can not connect it with the same phone .And the chip will restart when we try to reconnet with the same phone (the phone have been deleted...
Dear friend,
The user experience of PPK desktop application is terrible. There is no guider about using this application in the PPK user guider 2.0. I got some problems...
Hi,
we are using the PPK for a while (Software version 1.0.0). For some reason the calibrated values haved changed and very high current values are showing up. I've recalibrated...
Hi Team,
S132 V5.0 for nRF52832 can support up to 20 links.
If the connected links have different ATT MTU setting, what is the behavior of the device/softdevice regarding...
Hi,
I am using nRF52832 SDK 14.2.0 and i added the header file in project path "nrf_dfu_svci.h" but still i getting the error ..\..\..\..\..\..\components\libraries\bootloader...
Hi all,
I am using segger studio , i am trying to run examples of mesh alpha sdk that nordic provides. I can able to dump the code on board successfully. But if i try to...
I am using the nrf_i2s driver, and it works properly ... with CONFIG.CHANNELS set to stereo.
But for my application, I only need to drive data onto SDOUT left channel. ...
Dear sir please help..its urgent.
i am using below configurations. Nordic - nRF52832-QFAA-B Soft device - 132 SDK - nRF5_SDK_14.2
I am following the "ble_app_att_mtu_throughput...
Hi all,
I am using the nRF51822 BLE with custom board, I want to configure Timer1 to generate IRQ for every 1ms and Timer2 to generate IRQ for every 1us. I want to run...
Hi,
I want to change the UART0 baud rate at runtime (the peripheral has switched to a new rate). Is it enough to reset to (say) 9600 baud, like:
NRF_UART0->BAUDRATE =...
Hello,
I am using the nRF52840 DK with Keil to develop. I have a structure defined as follows:
I have verified that uint8 is 1 byte, uint16 is 2 bytes, and uint32 is...
Hi,
I am using nRF52832 Dk and SD132, sdk is 13.1. I have sent my sensor data to server using external wifi module which is interface with nRF52832 DK.
Everything working...
I have a Client and two Server, so i did flash the example code.
But, from the command '3', i get an error that i do not know.
Can you help me ?
What is correct value...
Hi.
I want to add constant descriptor. Can I save the memory using const variable and BLE_GATTS_VLOC_USER. Will it occur some faults in future?
static const uint8_t value...
I am developing a program with BMI160 with this libraries , but I do not know to which it refers the following code at line 5 and 6: sensor.read and sensor.write.
It is...
