Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I would like to know the part number for the Side facing RGB LEDs used in the Nordic Thingy 52. I couldn't find the Bill of Material for the Thingy 52.
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
Dear nordic employee
My 52832’s GPIO control the external 32mhz crystal‘s power，
when the 52832 work in the sleepmode ,I cut the 32mhz crystal'power
then when I want...
Hi I have a problem with TWI (the slave part), that is, we can only receive on nrf52840 8 bit, there is someone who knows how to do so you can receive 16 bit, we have taken...
Is there possible to get timer period shorter than 12us with nRF51 and SDK 14? "timer" example with PCA10040 works correct, but with PCA10028 not. When set timer period lower...
When I go to build any of the nRF SDK BLE examples, I get linker errors that app_error_handler was not found. I now copy-and-paste a boilerplate version of that into the code...
Hello,
I'm currently trying to OTA update the firmware of my nRF52832 DK, I use the SDK 12.3.0.
I loaded the BLE Secure DFU Bootloader in the DK, it's advertising as...
Hello, i use nRF5_SDK_12.3.0_d7731ad. I took this tutorial https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and according to...
Hi, Guys,
I am using nrf52832 for our product. Recently I updated stack and sdk from s132v2/sdk12.1 to s132v4/sdk13. However, I see a new characteristic under Generic Acess...
Hello,
I'm trying to run the example ble_app_uart using nRF52840PDK and iOS 11.
The device appears as Nordic_UART but when I connect, nothing shows up. The following screen...
Hi! Compiler errors are popping up when working on nrf_drv_rtc.c while log is enabled for this nRF module. I see that the problem is any log statement that contains EVT_TO_STR...
Good afternoon,
I have been doing some tests with the nRF SDK for Mesh v1.0.0, and have a question regarding it.
I'm using a fw based of the Light Switch example, to...
By using the DFU to transfer an updated version of the application, The nRF Connect tool pop-up tip:"upgrade succesfully". But the version of application mostly is still older...
