When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
In our application we don't allow bonding. Therefore I'm not allowing the application to send peer data to the bootloader using dfu_app_peer_data_set()...Therefore...
In NRF52-DK, I am currently working on NRF5 SDK 11.0.
In examples/peripheral/spi/pca10040/,
The master spi device is continuously sending "Nordic" string every 200msec...
I've submitted my product using nRF51822 chipset for Bluetooth certification. The BQE asks for QDID of proximity profile. Anyone knows about the QDID #?
Thanks,
Hello,
Is there a way to test packet corruption? My setup would be that I have my FW in nRF52-DK. Then I would test communication using nRF51-Dongle. I would like to force...
I want to connect two nRF51822-BKs and find their proximity. If one of the beacons go >5m away from the other beacon then one should beep/LED ON.
What is the best way to...
I have some troubles to understand the system clock functionality.
I am using a Module from Rigado which uses the nRF52 and has an external 32Mhz osc. on board.
In the...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
hi
i didn't manage to find detailed requirements on the voltage from the chip.
in the spec i see voltage range of :1.7-3.6v
but its not enough data for designing converter...
hi everyone, I am new to developing apps for nrf51822, and currently I want to learn first, I tried to google a lot around and could not look for the right resources, it would...
hi,
I would like to connect hid keypad with ipad,phone5s and android phone(all these have Bluetooth version 4 )but i couldn't connect this.ie, The nrf51822 module advertising...
I attempted to capture a waveform when running the SPI master example on nFR52 SDK/PCA10040. The source code I have as default and showing as follows
#define SPI0_ENABLED...
Hello,
We are working on a project that includes a countdown but we could not able to do it. Simply we want to do this:
Nrf51822 receives a signal-->run our funcion...
Recently, I've built up the latest OpenMesh v.0.85 example among 3 pieces of nRF51DK successfully. For my application, I would like to increase the data payload, is it possible...
Hi,
I am using Gazell for communication between two nodes. The first node is sending a sensor reading to the second node (which will be called henceforth the sink node...
Hello everybody
I have a nRF905 circuit sealed in a different medium than air and I am facing an 8 dBm power loss after sealing. I would like to know the following: Is...
