Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
I'm attempting to setup GPIOTE for an output that is set and cleared by different events. The GPIOTE driver doesn't let me initialize an output twice. Is there a way to do...
I have 2 objectives BT beacon and concurrent ESB with Thread using time slotting A. I would like my thread devices to broadcast BT beacons. As this does not require any reception...
Hello. We have product based on NRF51822 chip. 24 bit 4 channel ADC connected through SPI to MCU. Data rate is 250 Hz (4 ms). We send two ADC samples evry notification packet...
I started setting up Zephyr SDK development on my W10 laptop, according to the nRF Connect for Desktop guide, but running into this error when executing pip requirements installation...
Hello,
I'm writing a BLE app that acts as a peripheral and a broadcaster. If a connection is established, I'd like to continue advertising but update the advertising parameters...
Hi,
I am migrating sdk 15.2 to 15.3. Everything works fine, except the nrf logging. Currently, I am using RTT configuration, with default backend enabled. The code is simple...
