Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi, I'm looking for a PCB antenna design for nRF52832 based on 0.8 mm thickness four or two layers stack up .
I found some examples but based on pbc of different thickness...
Good morning,
I'm designing a new product based on the nRF52840 device (s140) and power consumption is one of the key parameters for my project.
The equipment (peripheral...
I'm debugging some corner-cases with my own DFU process and Bootloader. I believe I hit a race condition in which sd_mbr_command() was called before the source of the new...
I am trying to make a service discovery on a peripheral device using a nrf52-DK (pca10040). I built my project around the multi-discovery example from SDK 15.3.
When performing...
Hey all,
I'm trying to replace the nrf_cli_uart transport layer with the CDC ACM equivalent (nrf_cli_cdc_acm), since I have an nrf52840 dongle and can't use the uart libraries...
OS : Ubuntu
SDK: 15.3.0_59ac345
Base example : peripheral/saadc
HW : nRF52832 DK PCA10040 1.2.1 2017.49 682663245
Hello, i would like to make sure the ADC acquisition...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to check for debounce of a level on...
Dear support,
What are the absolute minimum decoupling cap sizes running the nrf52810? The application is extremely power sensitive and it is not desirable to have any...
Hello
I am trying to add two custom UUID as below ( Platform nRF52) . And the API return error when I call the second time, with a different UUID .
err_code = sd_ble_uuid_vs_add...
Acually i m working on a project which calculates distance using RSSI values , and i am having this doubt whuch examples to refer between ble_central and ble_peripheral
...
Hi,
I want to configure "BLE_GAP_PHY_2MBPS" in ble_app_uart example of sdk 15.3.0 for faster communication, for this i have changed
BLE_GAP_EVT_PHY_UPDATE_REQUEST: { ...
Hello community,
I am trying to obtain minimum current consumption in dk. I found lot on internet but currently there is no example code for RTC and PSM mode.
Can anyone...
Hi,
In the documentaton nERF52832_PS_v1.4, the common mode rejection ratio of the ADC when used in differential inputs is not given in the electrical specifications, where...
