Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I am working on project where I am storing and reading data from an SD card. During the initialization, I would like to print the full contents of the root directory - "/...
Hello,
I have a problem through which unfortunately I'm not able to come across alone. I'm using nRF52832 with softdevice and UART central example from SDK14.2 (..\examples...
I'm using nRF52840-PDK. I created a custom ble service following this tutorial ( github.com/.../custom_ble_service_example) and sent my sensor data over bluetooth. Now I'm...
Hi ,
I am trying to disconnect a connected central (phone) by calling sd_ble_gap_disconnect from my nrf52 configured in multiperipheral mode. . The disconnect call returns...
I am trying to time a capacitor discharge through different resistance sensors for greater resolution than an ADC. I did this using the GPIO functions initially but the SD...
Hi,
Is it possible to use Segger Embedded Studio with nRF51?
I see on your web site it's supported with SDK 14 or greater but this SDK is only for nRF52.
My product...
I have problems with my custom board.
I developed the firmware with the nrf52840-PDK and there the firmware runs standalone (with RTT connected and without) or when debugged...
Hello
I am working on nrf52382,sdk11,softdevice 2.0.
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-fd3fce63fa6d4ddfa73158194e4d87c3/battery_5F00_pins...
Hello,
I am writting a batch script to flash a PCA10056.I use it to flash the softdevice, the bootloader and my application.
The script works well and flash the device...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device.
Here is my Schematics
here BATTERY is connected...
Hi
I am working with the twi_scanner_pca10056 example found in the SDK. Using a oscilloscope I can detect the logging messages on pin P0.01, even though sdt_config.h defines...
Hi all, when I modify ble_central for connect multi peripheral via NUS. I got error : BLE_DB_DISCOVERY_ERROR in funtion
So, can you show me how to solve it . Thank very...
Hi there,
Is possible use nrfjprog to write in flash the data time using windows batch commands after programmed the device?
actually, I want to use the nRF52 as a RTC...
I have a question about the nRF52840 QIAA Reference Layout v1.0 which can be found in the infocenter /nRF52 Series/Reference Layout. I saw that it has keepout areas on mid...
