When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I am trying to implement the DFU ANT Bootlaoader on my PCA100040 board. I have uploaded the softdevice S212 and the bootloader with nRFgo Studio. I have an ANT dongle...
Hi, I want to read the StaticPasskey from the Softdevice that was set before with:
uint8_t u8_ToBePassKey[];
/*
* Configure ToBePassKey in some way...
*/
m_static_pin_option...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
According to here , pstorage_init should not be initialized twice.It links to another thread and the documentation which says the same but does not mention downfalls of doing...
Hi,
I am trying to print ble device names around my board by scanning and i am able to print some devices and i am unable to print other device names even though they are...
Hi. We recently upgraded from SDK13 to SDK14. All was well until we integrated the bootloader. We are using Laird's BL652. We updated the bootloader's config to use NRF_CLOCK_LF_SRC_RC...
Hello All,
I am new to this area and i am just starting my development for BLE.
i am planning to use nRF52832 . I want to know that if i am planning to make night lamp...
Hey,
I'm new to the Nordic Semiconductors and wanted to get started out trying to learn about Bluetooth Mesh.
I've been reading a lot of posts and trying to get some...
------------ EDIT Sep-21-2017 ----------------
I was able to work around the issue by trying on a Linux distribution. Here is a written guide to the package install and...
Hi,
I have successfully connected an MCP3004 to the nRF52832 and can assign the ADC channel 0 output to a characteristic value. Works beautifully.
However, there are...
Hello,
I would like to know what are possibilities for low power in a central device on nRF52 chip.
I need to be in BLe connection mode, and be able to receive notification...
I'm trying to figure out if the NRF51822 is capable of performing the tasks I need for my project. I need to be able to do the following
4x PWM at ~2kHz
4x Analog read...
I am building a Bluetooth Mesh project and when trying to make a custom Makefile for the Mesh Light Control Example , but when compiling the project i get this error:
Compiling...
