Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I currently have a problem with the gpiote setup. I'm using it to detect an interrupt from mma8652 accelerometer.
here is an annotated version with the key portions of...
Hi,
I've been trying to integrate the secure bootloader witrh SDK12 into my device, which had been working fine with the old bootloader and SDK11.
I've swapped everything...
Hello,
sd_softdevice_enable give me a hardfault every time. What can I do ?
Configuration:
Jlink / Ozone
Confirmed on 2 Sparkfun nRF52832 boards (nRF82832 AA rev 1...
Hello, I am trying a simple btle application where one mcu will send a "help" message and another will respond with its address. The mcu that asks for stores the address of...
Hello,
I would like to implement the nordic DFU protocol natively in a new app as I have historically found it tiresome and buggy to turn the DFU program into a library...
Hello, I am using eclipse app development, to achieve OTA function, use Maven to download DFU library, can not find the library, see your introduction： compile'no.nordicsemi...
I have a BLE circuit utilizing an NRF52832 cpu/integrated radio, necessary impedance matching network and a single ended micro-strip "L" antenna. How can I determine the gain...
I an trying to wake the chip and record the temperature readings when temperature reaches a certain threshold (eg: 80 deg C), can this be achieved using built-in temperature...
I debug the DFU Bootloader through UART,I am sure the APP code is complete updated,but the application does not run when the device is after bootloader to auto soft reset...
Hello:
I'm trying to get an example program ble_app_hrs running on my custom board, because earlier last month I couldn't write the cccd descriptor properly and I suspect...
i try to connect and read and write on my device with ionic2 BLE plugin , i can connect and also write on the device but when i try to read a data from device and use startNotification...
Dear team,
Our customer using "nRF51422 Development KiT8PCA10028)" with "ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex".
They can check advertising packets, but, they...
Hello,
Here is a newbie question:
I have NRF52832 (sparkfun breakout board) and ADT7410 temperature sensor and, I want to create a data logger. But, i could not understand...
Hii all,
Is there any one started using and succeed with nRF connect 2.0, I installed and open this app, and added two apps two this
After that I launched the app...
