Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Faced with problem in subject during porting Serialisation to STM32F4 chip.
Serialisation library extensively uses function call triggered by NVIC.
How to substitute this...
I'm using ANSC example, pca10028, iphon5s and iphon4s.
I confirmed #define DEVICE_MANAGER_MAX_BONDS 7.
But pca10028 cannot pair with iphone5s after paired with iphone4s...
Hi,
I'm using nrfutil to update my nRF52832.
I change target from nRF51822 to nRF52832 and I want be able to bootload my target through own master.
In past, I used...
I have followed instructions at the link below to setup a Raspberry Pi 3 as a 6lowPAN router, and am trying to run the dns example from nRF5 IoT SDK 0.9.x on an nRF52-DK:...
Hi,
I'm using pca10040 and prebuild hex with s132 from sdk 12. Now I'm wondering how can I get number of sent data? If I set it as transmitter - send via uart 0x8094 i...
Hi all.
What happends on peripheral side when I use long write by sd_ble_gattc_write as devzone.nordicsemi.com/.../ ?
How Can I read it on peripheral ?
Can I use once...
hello there i want to use low power comparator nrf51. now my device work with battery. so i think i require internal reference. now can you tell me how to use internal reference...
Hello, recently I've found an information about bit counter in Radio Module in nRF52 Product Specification. Unfortunatelly I can't find any reference at infocenter how to...
Is MTU of all BLE devices limitted to 23 bytes when using ATT protocol?
I don't know explicitly.
Some say it is possible to use MTU longer than 23 bytes.
Others say...
I am using TAIYO-YUDEN EYSHCN, which is having Nordic-nRF52832 chip on it. As per document from TAIYO-YUDEN, recommended to flash s132-firmware on it. I downloaded s132_nrf52_3...
I have two questions with the remaining unresolved symbols being the most critical. I will decribed the situation I have encountered as a sequrence of chronological steps...
Hello,
I have a need to construct multiple portable devices on a short time frame. We expect that building Arduino-format shields for our peripherals and using nRF52 DK...
I am using PWM on a BLE Nano using Nordic SDK. I was having problems with the PWM and decided I would set the duty cycle to 0 to see if the program was working right:
#include...
I'm trying build a file in Keil, and have received this error below. Please advise on how to fix it! Thanks!:
*** Using Compiler 'V5.06 update 3 (build 300)', folder: ...
