Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
Hi,
Is there any documentation regarding nRF OpenMesh( nRF51-ble-broadcast-mesh) Security ? Explaining the security of the communication between nodes in the Mesh network...
Hi all,
I'm working on mbed os and I cannot use the softdevice_ble_evt_handler_set and SOFTDEVICE_HANDLER_INIT . Every time I build it, I get:
undefined reference to ...
Hi ,
I am using S120 ble_app_multilink_central example. I have configured UART0 in interrupt mode. I send some command and expect some response. It work very well in starting...
Our product is based on nrf51422_CEAA chip with softdevice S110, SDK 8.0.0, dual bank ble bootloader DFU.
We have modified the dfu bootloader example from SDK 8.0.0 to...
I read a document, "Setting up production test using DTM", "nAN-034 Application Note v1.0".
And, Figure 3 shows how to setup test environment.
But, I cannot find which S...
DCDC_testing.zip
Hi,
I am in the process of reducing power consumption in micro esb mode. I use the following code, just for testing. The following code consumes 18mA unlike...
It is possible to load a new firmware in a NRF51822 PCBA using the Nordic Development Kit NRF51DK?
Do I need a special connector?
This is the beacon Module I pretend...
Hello,
I have a board with an RFDuino on it which uses a Nordic nRF51822 internally. We are seeing a few of them auto-brick when the input voltage dips too low.
My first...
I have a question about the usage of Flash Data Storage, chunks and parsing of the data retrieved from FDS.
How, when and why are you supposed to use "chunks" when setting...
Hello,
I would like to implement an interface with an external SPI ADC using the nRF52832.
The ADC has a RDY (ready) signal that goes low every time a new sample is ready...
Hello,
I have simple custom PCB with nRF51822.
I am trying to make it advertise like a beacon, by program it with ble_app_beacon example from nRF5_SDK examples.
I have...
I'm playing around with the experimental ble hrs with NFC pairing example, and I cannot seem to get it to work with my Android 6.0.1 Moto X Pure. I tap the phone to the NFC...
