Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi everybody.
I am making an application using ANCS, I saw that the original ANCS application saves some data to flash memory via device manager module and the parameters...
Is there a way to get to an softdevice/radio event, which is generated every time an advertising packet is send? I need to set a pin in high state while sending a packet.
Hi,
In my application, I am using nus service with S110 V7.1.0 (nRF51822). I faced to one problem that the rx channel is set up to notify characteristic. In iOS (8.3),...
My question is while the application is running, how can I disable the NUS service to turn on the DFU service. This idea stems from this question: devzone.nordicsemi.com/...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I've testing a Raytac mdbt40 module and I'm running the ble uart example (sdk 9.0, gcc debug enabled, no gcc optimization) and no external 32khz crystal
I can scan and...
Hello,
i would like to update my SDK to SDK11, but i'm not sure that the pack installer in keil works..
What are the different versions of the pack?
I 've this one...
Hello All,
The compatibility matrix states that the sdk for rev 2 devices has been discontinued on version 6.1.
We have some other products with rev 3 devices where...
Hi!
I'm using nRF51DK with s110_nRF51_8.0.0 Soft Device and SDK_9.0.0.
My application reads ADC with frequency 500Hz (2 bytes of data from one sensor each read), and twi...
I am just wondering about the status of nrf52 support for the mbed platform (specifically as a yotta target).
I have seen a number of other threads on both the nordic side...
I am developing an application on a STM32 CPU that uses a 51822 through BLE serialization for BLE connectivity.
I have connected some LEDs at the pins of the 51822 to indicate...
Hi,
The nRF51WLCSP needs IR blocking coating and I found here that an example epoxy can be Epo-tek 320. I just want to check if there is any specific time for covering...
Hi
I have been able to successfully write using FDS but I'm unable to read back using the same keys. Here are my code snippets:
#define FILE_ID 0x1111
#define REC_START_ID...
Hello~
I'm using JLinkEXE to flash an nRF51822 chip. When I use nrfgo and press "erase all", it wroks. But after if I flash the s130, I can't erase the s130 with command...
