Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I try to run a dual mode(peripheral/central) with S130. I'm using SPI serialization and sending command form an external MCU. I try to follow the example ble_app_hrs_rscs_relay...
Hii all,
I am trying to work with dfu, I developing an application that works with dfu, when I flash the softdevice and bootloader the device advertising as dfutarg and then...
I've loaded the S210_nRF51422_5.0.0 softdevice on my board from the nRFgoStudio.
I compiled the ant_hrm_tx_auto_s210_pca10028 project with no problem. However, when I try...
Hello,
I am developing two systems. One is a peripheral that advertises both a beacon and a ble peripheral custom service (using nRF51822 with s110 softdevice). The second...
Hi,
I am trying to use an nrf51822 with a sensor that outputs value between 0-5V. What I am confused about is how to read input voltage on the beacon. I saw some people...
Hi,
I need to debug my perpheral device, but as I know if I do debug when SD is running, it can cuase the time sync issue, then cause the hard-fault. I know there's a way...
hi ken：
I use Nrf52832(S132) to act as central and peripheral at the same time, which like the project ...\nRF52_SDK_0.9.0_0c82e3e\examples\ble_central_and_peripheral\experimental...
Hi,
I run ADC mudule together with SD, but go into hardfault eatch when I release the HF-clock.
Chip: 51822
SDK : 10.0-alpha
IDE : Keil-472
I use this function...
Hi!
I have inherited a large codebase that I'm trying to migrate to SDKv10 from SDKv6.
The project also uses an A4960 BLDC motor controller. To bring the motor up to...
Hello,
Is my ram reservation right for nRF52 with S132 ?
see in app_ram_base.h APP_RAM_BASE_CENTRAL_LINKS_3_PERIPH_LINKS_1_SEC_COUNT_3_MID_BW = 0x2F50
RAM (rwx) ...
Hey,
I have been trying to create a notification characteristic for nrf51822. Whenever I add char_md.char_props.notify = 1; lightblue doesn't connect to it.
I do get a...
Ok, this one seriously has me stumped...
I have a custom bootloader that is modified from the DFU example (SoftDevcie S110 8.0, with SDK 9.0, using gcc). BLE is not used...
What is the distance that a nRF24L01+ correspond to for 0db, -6db, -12db, -18db output powers.?
I mean what will be range of the chip for these output powers.?
Thanks...
Hi all,
Hope someone can help me. We are using the NRF51822 on MDBT40-256V3 module. The IC used is revision V3. We're not using Bluetooth but our own proprietary protocol...
