hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I am using GPIOTE interrupts to detect button presses. It works fine but there are only four channels in GPIOTE->EVENTS_IN[] and each channel can only be assigned to...
Hello,
I'm using exeprimental dual mode example with my Beacon kit. I ported the example to work with pca2006, but i'm having problems with led. On my mkit, leds work just...
This is what happens when linking my project in Eclipse:
make all
'Building target: project_name.elf'
'Invoking: Cross ARM C Linker'
arm-none-eabi-gcc -mcpu=cortex...
Hello,
We would like our app to only be seen by:
Devices that have previously connected
Devices that we allow to be added to the whitelist via the temporary disabling...
In my pursuit to make a stable Gazell streaming device, I noticed some issues with pushing packets to the Tx FIFO.
Even through I get an affirmative response from the nrf_gzll_ok_to_add_packet_to_tx_fifo...
Hello,
After I connect my iPhone with a 8001 nordic chip without opening the characteristic I receive a pipe status event which says that the pipe is opened. This is totally...
Hi,
I would like to use the softdevice s130 because i want to try having a nrf58122 as a ble central and peripheral at the same time.
At the moment, there is still the...
Hey everyone,
I have an application where I have to write data to a characteristic. I would like to only allow reliable writes (not unacknowledged ones). Is this permitted...
Hello,
I'm having problems with defining RGB led on my beacon (pca20006). When i define for example RED led (on pin 12) with code nrf_gpio_cfg_output(12); i should be able...
Hello,
I am trying to load ble_app_beacon code provided in nordic sdk to redbear lab's ble nano. I am using sdk version 8.0.0 and soft device(s110) version 6.2.1 .
I am...
If BLE device is sleeping,is link layer connection terminated or the link layer connection is still valid..?
if it is valid..how the master will know about the sleeping periods...
Hi all.
Consumption current increases by about 1.5 mA after a battery check.
uint8_t battery_start(void)
{
// Configure ADC
NRF_ADC->INTENSET = ADC_INTENSET_END_Msk;...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
